Autonics ADS-SE2 Series Panduan Produk - Halaman 3

Jelajahi secara online atau unduh pdf Panduan Produk untuk Aksesori Autonics ADS-SE2 Series. Autonics ADS-SE2 Series 3 halaman. Automatic door side sensors

Halaman Cetak

Dimensions

• Unit: mm, For the detailed drawings, follow the Autonics website.

•

part is only for ADS-SEC2.

■ Controller (ADS-SEC□)

■ Sensor (ADS-SHP)

• One push method

150

1.7

Ø 2.4, 10 m

Operation Indicator

Power

Entry activation

OFF

Operation indicator

OFF

(red, green)

N.O.

OPEN

Output

contact

N.C.

01) It operates in the normal. None of the person or the object is in the between sensors.

02) The state after the person or object has passed.

Sensitivity Adjustment

This function helps to set the sensitivity in the situation that if the malfunction occurs

due to the lack of sensitivity, when installing this unit at first or during operation.

Depending on the sensing distance, the controller automatically sets the optimum

sensitivity for the best operation.

■ Steps of the sensitivity setting

• When pressing the sensitivity setting key below 1 sec, the sensitivity setting is

canceled and it operates as the latest setting.

• If sensitivity is not enough or the setting is not correct, this unit may have

malfunction.

Sensitivity

Press sensitivity

during pressing

setting key

setting key (TEACH)

sensitivity setting

Sensitivity

Red/green indicator

setting

cross-flashing

indicator

01)

Ready for

Statue

sensitivity setting

01) The indicator may vary depending on the channels. See the 'Sensitivity Setting Indicators.'

■ Cautions during the sensitivity setting

• Check there are obstacles between Emitter / Receiver heads.

• Check there is dirt on the head lens of Emitter / Receiver.

• Check the wires are disconnected or connected properly as the label (nameplate).

• Check the heads of Emitter/Receiver are inclined.

• Check the above items and resolve the problems and set the sensitivity again.

Troubleshooting

Malfunction

Cause

Power voltage

It is not work.

Cable cut, disconnection

Rated sensing distance

Sometimes it does

Pollution by pollutant on the

not work.

lens of Emitter/Receiver.

Rated sensing distance

There are obstacles between

The door is opened

Emitter and Receiver.

even if people do not

enter in the sensing

There are equipments generating

area.

strong noise or ratio wave (motor,

neon lamp, generator and high-

tension wire, etc).

• Screw method

150

11.5

Ø 2.4, 10 m

M10×0.75

Out of the

Enter the

Out of the

sensing area

01)

OFF

OPEN

After 1 sec.

key

Red/green indicator

all OFF

flashing at the same time

Starts

Completes

sensitivity setting

Troubleshooting

Check the power cable and adjust

power voltage.

Check wiring and terminals.

Use it in rated sensing distance.

Remove the pollutant.

Use it in rated sensing distance.

Remove obstacles.

Keep away from the equipment

generating strong noise or ratio

wave.

Unit Descriptions

<ADS-SEC1>

OUT 1 indicator

Wiring connection

button

Emitter/Receiver sensor

connector terminals

01) ADS-SEC1: 6 to 9, ADS-SEC2: 6 to 13

Sensitivity Setting Indicators

Indicator

Connected

channel

OUT1 (red)

Flashing

1 CH

02)

Flashing

OFF

2 CH

Flashing

OFF

Flashing

OFF

• For ADS-SE2, OUT 1 indicator (red) is for the receiver status set by the emitter of 1-channel

and OUT 2 indicator (green) is for the receiver status set by the emitter of 2-channel.

• If the lack of sensitivity occurs by not-matched optical axes or pollution on the lens of

emitter / receiver during self diagnostic function, for ADS-SE1, the OUT 1 indicator (red)

flashes. For ADS-SE2, the OUT indicator of the channel with the lack of received light

Completes

the process of

flashes.

the key

Indicates

Sold Separately: Mounting Bracket

operation status

• Unit: mm, For the detailed drawings, follow the Autonics website.

■ ADS-SB12 (one push method) ■ ADS-SB10 (screw method)

Ø 12.2

M4 flat head

cap screw

18, Bansong-ro 513Beon-gil, Haeundae-gu, Busan, Republic of Korea, 48002

www.autonics.com | +82-51-519-3232 | [email protected]

<ADS-SEC2>

OUT 2 indicator

Mounting hole

01)

Status

After setting the

OUT2 (green)

sensitivity

Sensitivity setting

OFF

success

Sensitivity setting

Flashing

failure

OFF

1, 2 CH: sensitivity

setting success

1 CH: success,

Flashing

2 CH: failure

OFF

1 CH: failure,

2 CH: success

1, 2 CH: sensitivity

Flashing

setting failure

OFF

M10×0.75

M4 flat head

cap screw

Sensor body

Lens

Head

holder

Nut

Sensor head

<ADS-SHP>

Sensitivity setting key (TEACH)

Power and output connection

terminal (1 to 5)

In operation

Received light

Emitter disconnection or

sensor cable extension

Lack of sensitivity

Interrupted light

1, 2 CH: received light

2 CH: lack of sensitivity

1 CH: received light,

2 CH: interrupted light

1 CH: lack of sensitivity

1 CH: interrupted light,

2 CH: received light

1, 2 CH: lack of sensitivity

or emitter disconnection

1, 2 CH: interrupted light