Hifionics BRUTUS BRX2400.1D Panduan Petunjuk Instalasi - Halaman 3

Jelajahi secara online atau unduh pdf Panduan Petunjuk Instalasi untuk Penguat Hifionics BRUTUS BRX2400.1D. Hifionics BRUTUS BRX2400.1D 13 halaman. Brutus brx series amplifers

Halaman Cetak

AMPLIFIER FEATURE DESCRIPTIONS

BRUTUS BRX AMPLIFIERS:

Each model is capable of 4 & 2-Ohms stereo per channel, or 4-Ohms mono bridged operation except the

mono amps which are capable of 4, 2 and 1-Ohm loads.

Tri-Mode operation with any stereo pair of amplifier channels is possible, as with all bridgeable amplifiers.

The input sensitivities for rated output powers are variable from 0.2V to 6V for the multi channel amplifiers

and 0.2V to 9V for the mono models.

All crossovers are fully variable in their respective ranges.

Crossover filters are 12dB/Octave.

1 set for channels 1 & 2.

The X-OVER slide switch selects the internal crossover functions:

-The input signal is routed directly to the LINE OUT RCA jacks, regardless of the X-OVER setting simplifying

daisy chaining of amplifiers.

-HPF: Selects the built in HI PASS filter.

-FULL: Bypasses all crossovers for full frequency range operation.

-LPF: Selects the built in LOW PASS filter.

MODE: Selectable Stereo or MONO operation.

HPF: Variable low frequency cut off from 60Hz to 1.3kHz.

LPF: Variable high frequency cut off from 30Hz to 250Hz.

BASS EQ: 45Hz bass boost variable from 0dB to 12dB.

LEVEL: Variable LEVEL (GAIN) control from 6.0V to 0.2V.

LINE INPUT: The line input accepts unbalanced (RCA) inputs from 0.2V to 6V.

LINE OUTPUT: The line output passes through signal from the line inputs which allows you to daisy chain

multiple amplifiers from one signal.

The 4 channel amps have the same features as the 2 channel models except that there are 2 sets of

controls.

1 set for channels 1 & 2 and 1 set for channels 3 & 4.

In addition, the 4 channel models have a Mode switch which allows you to select 2 or 4 channel operation.

Switch to 2 channel if you only have 1 set of RCA's in CH 1/2 and the unit will automatically

supply signal to channels 3/4. Select 4 channel if you are providing RCA's to channels 1/2 and 3/4.

The X-OVER slide switch selects the internal crossover functions:

-The input signal is routed directly to the LINE OUT RCA jacks, regardless of the X-OVER setting simplifying

daisy chaining of amplifiers.

HI PASS: Variable low frequency cut off from 10Hz to 1.5kHz.

LOW PASS: Variable high frequency cut off from 30Hz to 150Hz.

BASS EQ: 45Hz bass boost variable from 0dB to 10dB.

LEVEL: Variable LEVEL (GAIN) control from 6.0V to 0.2V.

The 5 channel amps have the same features as the 4 channel models except that there are 3 sets of

controls.

1 set for channels 1 & 2, 1 set for channels 3 & 4 and 1 set for channel 5.

In addition, the 4 channel models have a Mode switch which allows you to select 2, 4 or 5 channel operation.

Switch to 2 channel if you only have 1 set of RCA's in CH 1/2 and the unit will automatically

supply signal to channels 2/4/5. Select 4 channel if you are providing RCA's to channels 1/2 and 3/4 and

signal will be internally routed to Ch5. Select 5 if you are supplying RCA's to each INPUT.

The X-OVER slide switch selects the internal crossover functions:

-The input signal is routed directly to the LINE OUT RCA jacks, regardless of the X-OVER setting simplifying

daisy chaining of amplifiers.

HI PASS: Variable low frequency cut off from 10Hz to 1.5kHz.

LOW PASS: Variable high frequency cut off from 30Hz to 150Hz. (CH3/4 & 5)

BASS EQ: 45Hz bass boost variable from 0dB to 10dB.

LEVEL: Variable LEVEL (GAIN) control from 6.0V to 0.2V.

REMOTE: This is a remote input jack for the remote level control on Ch5.

SUBSONIC: Crossover filter from 15Hz to 35Hz.

LOW PASS: Crossover filter from 35Hz to 250Hz.

LEVEL: Adjusts the input sensitivity from 0.2 volts to 9 volts.

BASS EQ: Adjustable bass boost from 0db to 10dB.

PHASE:

The Phase Shift is fully adjustable from 0 to 180 degrees and this allows you to control time

alignment.

REMOTE: This is the input jack for the remote Level control.

BALANCED INPUT:

Accepts line level balanced input from 0.4v to 18v.

LINE INPUT: The line input accepts unbalanced (RCA) inputs from 0.2V to 9V.

LINE OUTPUT: The line output passes through signal from the line inputs which allows you to daisy chain

multiple amplifiers from one signal.

-The LINE INPUT signal is routed directly to the LINE OUT RCA jacks, and not affected by the settings on the

amplifier simplifying daisy chaining of amplifiers.

The BRX2400.1D is identical to the other BRX mono amplifiers except that the BRX2400.1D is a

linkable amplifier and features a MASTER / SLAVE selection switch and IN / OUT RCA connection. This

allows for a pair of amps to link at 2-Ohms and produce 4800 watts rms.

A POWER LED indicates the powered up and turned on condition.

All Hifonics amplifiers feature a comprehensive diagnostic system, with speaker lead short circuit, and

amplifier DC faults indicated by the red "PROTECT" LED.

CAUTION: DO NOT OPERATE ANY AMPLIFIER BELOW THE INTENDED IMPEDANCE. YOU WILL

CAUSE DAMAGE TO THE AMPLIFIER THAT WILL NOT BE COVERED UNDER THE WARRANTY

PRINTED IN THE BACK OF THE MANUAL. 2 & 4 Channel amps are capable of 4 and 2-Ohms wired

stereo and 4-Ohms wired mono bridged. The mono amps are capable of 4, 2 and 1-Ohm.

BRX160.2 2-CHANNEL AMPLIFIERS

LINE OUT LINE INPUT

LEVEL

BASS EQ

FULL LPF HPF

0.2V

0dB

12dB

Note that the LOW PASS signal is MONO.

-In the LPF position, the HPF filter acts as a subsonic filter.

-When the LPF mode is selected, a 0 to +12dB, at 45Hz, BASS EQ is also switched in.

BRX320.4 / BRX640.4 / BRX1200.4 4-CHANNEL AMPLIFIERS

CH1/2

CH3/4

REMOTE

HI PASS CH1/2 X-OVER LOW PASS BASS EQ

FULL LP/BP

10Hz 1.5kHz

2CH

4CH

FULL LP/BP

10Hz 1.5kHz

LINE INPUT

MODE

HI PASS CH3/4 X-OVER LOW PASS BASS EQ

Note that the LOW PASS signal is MONO.

-In the LP/BP position, the HI PASS filter acts as a subsonic filter.

-When the LP/BP mode is selected, a 0 to +10dB, at 45Hz, BASS EQ is also switched

in.

BRX5000.5 5-CHANNEL AMPLIFIERS

LINE INPUT CH1/2 X-OVER HI PASS

LEVEL

FULL

Ch2

Ch4

10Hz 1.5kHz 6V

0.2V 10Hz 1.5kHz

30Hz 150Hz 0dB 10dB 6V

Ch1

Ch3

REMOTE LOW PASS BASS EQ

Note that the LOW PASS signal is MONO.

-In the LP position, the HI PASS filter on Ch3/4 acts as a subsonic filter.

BRX1100.1D / BRX1600.1D / BRX2000.1D MONO BLOCK AMPLIFIERS

BALANCED

INPUT

OUTPUT

INPUT

LEVEL

PHASE

0.2V

The mono amps are capable of 4, 2 & 1-Ohm loads.

Operating the amp below 1-Ohm can cause damage to the amp not covered in the

warranty.

BRX2400.1D MONO BLOCK AMPLIFIERS

BALANCED

INPUT

OUTPUT

INPUT

LEVEL

PHASE

REMOTE BASS EQ

0.2V

180

The mono amps are capable of 4, 2 & 1-Ohm loads.

Operating the amp below 1-Ohm can cause damage to the amp not covered in the

warranty.

X-OVER

HPF

LPF

MODE

POWER

MONO

STEREO

60Hz 1.3kHz 30Hz 250Hz

PROTECT

LEVEL

POWER LINE OUTPUT

30Hz 150Hz 0dB 10dB 6.0V

0.2V

PROTECT

30Hz 150Hz 0dB 10dB 6.0V

0.2V

LEVEL

HI PASS CH3/4 X-OVER

LOW PASS

LEVEL

HI FULL LP

30Hz 150Hz

0.2V

PROTECT

0.2V

POWER

2CH 4CH 5CH

LEVEL

CH5

MODE

SUB

REMOTE

BASS EQ

SONIC

LOW PASS

POWER

PROTECT

180

0dB

10dB

15Hz

35Hz 35Hz 250Hz

POWER

SUB

PROTECT

SONIC

LOW PASS

0dB

10dB

15Hz

35Hz 35Hz 250Hz

OUTPUT

MASTER

INPUT

SLAVE

OUT

Ch5