Hifionics Hifonics TXi4008 Panduan Pengguna - Halaman 5
Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Penguat Hifionics Hifonics TXi4008. Hifionics Hifonics TXi4008 15 halaman. Titan series high performance amplifiers
Halaman Cetak- 1. Table of Contents
- 2. General Installation Procedure
- 3. Amplifier Feature Descriptions
- 4. Txi4008 / Txi6008 2-CHANNEL AMPLIFIER APPLICATIONS
- 5. Txi4408 / Txi6408 4 -CHANNEL AMPLIFIER APPLICATIONS
- 6. Txi7508 A/B CLASS 1 CHANNEL AMPLIFIER APPLICATIONS
- 7. Txi1008D / Txi1508D D CLASS 1 CHANNEL AMPLIFIER APPLICATIONS
- 8. Features and Specifications
- 9. Setting up Systems after Installation for Best Performance
- 10. Troubleshooting and Diagnostics
- 11. Product Warranty
TXi4008 / TXi6008 2 CHANNEL AMPLIFIER APPLICATIONS
FULL RANGE STEREO
This is the most basic application for the TITAN Series 2 channel amplifiers.
1. Interconnect cable checklist:
Connect the LINE INPUTS to the Radio/CD with good quality RCA cables.
2. Crossover Switch:
The X-OVER switch must be in the FULL position.
3. Crossover frequency control checklist:
FULL RANGE
STEREO LINE INPUT
FULL RANGE MONO
This application illustrates the basic mono bridging method for all Hifonics 2 channel
amplifiers.
Interconnect cable checklist:
A MONO signal source is required, such as would be available from the mono sub bass
output of an active crossover, whether stand alone, or built into a head unit or equalizer.
Important:
Do not be tempted to connect the hot, or positive outputs, from any source
together to obtain a mono signal, as this could very well damage the output stage of that
source.
It is necessary to feed the SAME signal to both left and right inputs via a Y-adapter RCA
cable. Connect the mono speaker positive terminal to the RIGHT +, and its negative
terminal to LEFT -.
FULL RANGE
MONO LINE INPUT
VIA Y-ADAPTER
FROM MONO SOURCE
The HIGH LEVEL inputs are used when the radio/CD player does not have RCA cable outputs. You can connect the radio/CD player speaker wires directly
to the amplifier via the high Level Inputs.
N/A for full range operation.
4. Line Level:
Refer to the section "Setting up systems after installation for best performance".
NOTE: Minimum final loudspeaker impedances:
4 &-2-Ohms stereo mode or 4-Ohms mono mode
This amplifier will not do 1-Ohm stereo or 2/1-Ohm mono operation.
Switch setting checklist:
- The AMPLIFIER X-OVER switch must be in the FULL position.
Crossover frequency control setting checklist:
N/A for full range operation.
TIP:
wrong with switching in the low pass filter in these amplifiers for a steeper low pass roll-
off.
Minimum final loudspeaker impedance:
- 4-Ohms mono.
Use this connector for 2 CH amplifiers
GRAY: CH 1 Speaker Input +
BROWN: CH 1 Speaker input -
Black: Chassis Ground
GREEN: CH 2 Speaker Input -
White: CH 2 Speaker Input +
If you are using the mono sub bass output of an active crossover, there is nothing
Use both connectors for 4 CH amplifiers
ORANGE: CH 3 Speaker Input +
PINK: CH 3 Speaker input -
Black: Chassis Ground
BLUE: CH 4 Speaker Input -
YELLOW: CH 4 Speaker Input +
FULL RANGE
SPEAKERS
TO BATTERY + 12 volts VIA FUSE
REMOTE TURN-ON
CHASSIS GROUND
FULL RANGE
MONO SPEAKER
TO BATTERY + 12 volts VIA FUSE
REMOTE TURN-ON
CHASSIS GROUND
3