Dynamite PASSPORT Ultra Duo Panduan Instalasi - Halaman 6

Jelajahi secara online atau unduh pdf Panduan Instalasi untuk Pengisi Daya Baterai Dynamite PASSPORT Ultra Duo. Dynamite PASSPORT Ultra Duo 10 halaman. 100w lcd ac/dc multi-chemistry battery charger
Juga untuk Dynamite PASSPORT Ultra Duo: Buku Petunjuk (2 halaman)

Halaman Cetak
Dynamite PASSPORT Ultra Duo Panduan Instalasi

7 - NICkEL CYCLE ChArgINg

1. Connect the banana plugs of the battery adapter cable to the Power Output Black (–) and
Power Output Red (+), making sure that the positive and negative connectors are not reversed.
2. Connect the battery connector to the battery adapter cable.
3. Press the Left and Right Arrows on the LCD Touch Screen to scroll through the main menu
screens until you reach Program Select=Ni-MH/Ni-Cd.
Program select=NiMH
CHG
4. Press CYCLE.
NiMH CYCLE
Capacity
CHG Curr.
DCHG Curr.
DCHG End Volt
Press&Hold
BACK
5. Press a parameter to highlight that parameter.
6. Press the Up and Down Arrows to edit the parameter.
7. Press Select to save the parameter.
8. Press the top right of the LCD Touch Screen to get to the next set of parameters.
9. Once the parameters are at the desired settings, press and hold CYCLE.
10. The charger will check the battery and charger settings and cycle charging will begin. The
charger will beep and display the following screen:
NiMH CYCLE
Capacity
Current
Voltage
Resistance
Peak Temp.
11. Press the arrow in the top right of the LCD Touch Screen to see the rest of the Cycle information.
12. Press CYCLE to see the voltage and amperage applied to each cycle.
Data NiMH = Cycle 1/1
--CHG--
00.00Vp
00000mAh
13. Press Graph to see the battery voltage graph. Press Back to return to the charging screen.
Data NiMH = Graph
14. Press STOP at any time to stop charging.
15. When cycle charging is complete, the charger will sound a series of beeps and display the
following screen:
NiMH DONE
Capacity
Current
Voltage
Resistance
Peak Temp.
16. Disconnect the battery from the charger.
6
N i M H
DCHG
CYCLE
[1/2]
:
50mAh
:
0.1A
:
0.1A
:
0.10V
:
CYCLE
SELECT
001:56S
:
47mAh
:
0.0A
:
8.00V
:
****mΩ
:
No sens
--DISCHG--
00.00Va
00000mAh
026:01S
:
671mAh
:
0.0A
:
9.25V
:
14mΩ
:
No sens
CAUTION: The Pb charge program menus are to be used ONLY for the charging and
discharging of Pb battery packs. Charging other battery types using the Pb charge
programs will damage the battery or the charger.

8 - PB ChArgINg

1. Connect the banana plugs of the battery adapter cable to the Power Output Black (–) and
Power Output Red (+), making sure that the positive and negative connectors are not reversed.
2. Connect the battery connector to the battery adapter cable.
3. Press the Left and Right Arrows on the LCD Touch Screen to scroll through the main menu
screens until you reach Program Select=Pb.
Program select=Pb
CHG
4. Press CHG.
Pb CHARGE
Pack. Volt.
Capacity
Current
Press&Hold
5. Press a parameter to highlight that parameter.
6. Press the Up and Down Arrows to edit the parameter.
7. Press Select to save the parameter.
8. Once the parameters are at the desired settings, press and hold CHARGE.
9 . The charger will check the battery and charger settings and display the following screen:
Pb Charge Confirm
-Connect-
Input • • • • OK
BATT. • • • • OK
10. Press START. The charger will beep and display the following screen:
Pb CHG
Capacity
Current
Voltage
Resistance
Peak Temp.
11. Press the arrow in the top right of the LCD Touch Screen to see the rest of the charging
information.
12. Press Graph to see the battery voltage graph. Press Back to return to the charging screen.
Data Pb
14.68V
13. Press STOP at any time to stop charging.
14. When charging is complete, the charger will sound a series of beeps and display the following screen:
Pb DONE
Capacity
Current
Voltage
Resistance
Peak Temp.
15. Disconnect the battery from the charger.
DCHG
:
2V/1P
:
50mAh
:
0.1A
:
CHARGE
-Check-
Set: 6P
Read: 5P
000:16S
:
8mAh
:
1.7A
:
14.69V
:
****mΩ
:
No sens
= Graph
BACK
000:12S
000:19S
:
8mAh
:
1.7A
:
11.60V
:
****mΩ
:
No sens