2gig Technologies 2GIG-BRDG1-900 Petunjuk Instalasi

Jelajahi secara online atau unduh pdf Petunjuk Instalasi untuk Router Jaringan 2gig Technologies 2GIG-BRDG1-900. 2gig Technologies 2GIG-BRDG1-900 4 halaman. Go!bridge ip communicator

Halaman Cetak

2GIG-BRDG1-900

GO!BRIDGE IP COMMUNICATOR

INSTALLATION INSTRUCTIONS

The Go!Bridge IP Communicator™ (2GIG‐BRDG1‐900) provides Internet

connectivity between the monitoring service's Central Station and the

Go!Control® Panel, when the panel is used as a household burglar alarm

system.

It supports automatic firmware updates, provides interactive security

services, and increases supervision using signal‐forwarding to the Central

Station. For wireless communication with the Control Panel, the 900MHz

Transceiver Module (2GIG‐XCVR) must be installed in the panel. For

Internet access, the Go!Bridge must be connected to the local network

router using an Ethernet cable (not provided).

Contents

Verify that the package includes the following:

•

1—Go!Bridge IP Communicator

•

1—5VDC USB Mini‐B Power Supply

•

1—Stand

•

1—Plastic Power Supply Bracket (includes Self‐Adhesive Backing

and Zip Tie)

•

1—Wall Socket Screw for Power Supply Bracket

•

2—Phillips Head Screws and Wall Anchors (to mount unit on wall)

•

4—Self‐Adhesive Vinyl Bumpers for use on unit or stand

Requirements

Before you install, program, and test the Go!Bridge IP Communicator,

ensure the control panel being paired with the Go!Bridge IP

Communicator meets these requirements:

•

Firmware Version 1.12 (or higher)

•

2GIG‐XCVR 900 MHz Transceiver

For compliance with UL 1023: Household Burglar‐

IMPORTANT:

Alarm System Units, the Go!Bridge must be installed in the

same room as the Internet modem or router.

NOTE: To protect data sent via the local wireless network, it is

recommended that you install the Go!Bridge IP Communicator on

a local network where either WPA (Wi‐Fi Protected Access) or

WPA2 (Wi‐Fi Protected Access II) encryption is already enabled.

After installing, programming, and testing the Go!Bridge IP

Communicator, you will need to register a new customer with the third‐

party monitoring service. See Registration on page 3.

Figure 1 Go!Bridge Front View—LED Indicators and Learn Button

A Network LED

B 900 MHz LED

C Learn Button

Powering ON the Go!Bridge IP Communicator

Use these steps to power ON the Go!Bridge IP Communicator:

Attach the power supply to the bracket (provided) as follows:

1a Insert the power supply into the enclosure on the plastic bracket.

See C in the figure below.

1b Secure the power supply to the retaining bracket by threading a

zip tie through the bracket's slots. See D in the figure below.

1c Remove the strip from the self‐adhesive backing on the power

supply bracket.

1d Affix the adhesive on the bracket to the wall outlet. Then secure

the bracket to the outlet with the wall socket screw (provided).

NOTE: Always use the provided power supply bracket in the United

States (and other countries where it is required). Canada does not

require the power supply retaining bracket.

Figure 2 Power Supply and Bracket

A 110V Wall Outlet

Plastic Power Supply Bracket with Adhesive Backing

AC Power Supply

D Zip Tie

Connect the Go!Bridge to the power source.

NOTE: Do not connect an Ethernet cable to the Go!Bridge IP

Communicator at this time. You will connect the cable when

completing the steps in Programming the Go!Bridge IP

Communicator into the Control Panel.

(Optional) Place the stand (provided) on a counter, desktop, or other

flat surface. Set the Go!Bridge IP Communicator in the stand.

NOTE: To protect surfaces from damage, affix the self‐adhesive vinyl

bumpers to the unit or stand.

Verify that the two (2) LEDs on the Go!Bridge IP Communicator

illuminate in RED. See Figure 1 Go!Bridge Front View—LED Indicators

and Learn Button on page 1.