Hifonics XXV XXV Sampson Panduan Pengguna - Halaman 9

Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Penguat Hifonics XXV XXV Sampson. Hifonics XXV XXV Sampson 20 halaman. Xxv edition high performance amplifier

Hifonics XXV XXV Sampson Panduan Pengguna
4 CHANNEL FULL RANGE SYSTEM
Here we show how to use the 4 channel amplifiers as straightforward discrete
4 channel full range units.
Interconnect cable checklist:
Connect the four inputs of the amplifier to a Radio/CD with good quality RCA
cables.
Crossover Switch setting checklist:
1 / 2 CROSSOVER: FULL
3 / 4 CROSSOVER: FULL
Crossover frequency control checklist:
Channels 1 / 2:
HI PASS: N/A
LOW PASS: N/A
Channels 3 / 4:
HI PASS: N/A
LOW PASS: N/A
Channels 1 & 2
FULL RANGE
STEREO LINE
Channels 3 & 4
INPUTS
2 or 3 CHANNEL FULL RANGE SYSTEM
Here we show how to use the 4 channel amplifiers as full range 2 or 3 channel
units by taking advantage of the mono bridging capability of all HiFonics
amplifiers.
The following example shows how to create a 3 channel system by mono
bridging channel pair 3 / 4. In order to create a 2 channel system, simply follow
the example to also mono bridge channel pair 1 / 2.
Interconnect cable checklist:
Connect the inputs of channel pair 1 / 2 to a suitable stereo source, e.g. a head
unit with good quality RCA cables.
A MONO signal source is required to bridge channel pair 3 / 4, such as would be
available from the mono sub bass output of an active crossover, whether
standalone, or built into a head unit or equalizer. Important: Do not be tempted
to connect the hot, or positive outputs, from any source together to obtain a
mono signal, as this could very well damage the output stage of that source.
It is necessary to feed the SAME signal to both left and right inputs via a
Y-adapter RCA cable.
Connect the mono speaker positive terminal to
the LEFT +, and its negative terminal to
RIGHT - as shown.
Crossover Switch setting checklist:
1 / 2 CROSSOVER: FULL
3 / 4 CROSSOVER: FULL
Crossover frequency control checklist:
Channels 1 / 2:
HI PASS: N/A
LOW PASS: N/A
1 STEREO
1 MONO
FULL RANGE
LINE INPUTS
XXV GEMINI 4 CHANNEL AMPLIFIER APPLICATIONS
CH4
BALANCED
PHASE
MONO MIX
CH1
CH3
INPUT
LEVEL
LEFT
9V
0.2V
0
180
2CH 4CH
CH2
CH4
OUTPUT
INPUT
9V
0.2V
-10
+10dB
LEVEL
CUT/BOOST BANDWIDTH
MODE
CH4
BALANCED
MONO MIX
CH1
CH3
INPUT
LEVEL
LEFT
9V
0.2V
0
2CH 4CH
CH2
CH4
OUTPUT
INPUT
9V
0.2V
-10
+10dB
MODE
LEVEL
CUT/BOOST BANDWIDTH
Level control checklist:
Refer to the section "Setting up systems after installation for best performance"
Minimum final loudspeaker impedances:
2 Ohm per channel stereo.
4 Ohms Bridged.
CH 1&2
PARAMETRIC EQ
AMPLIFIER
CH1 & 2
CUT/BOOST
HIGH PASS
ROUTING
RIGHT
0dB
BANDWIDTH
FREQ
FREQ
HP
CH3&4
X1 X10
X1 X10
FULL RANGE
CH1&2
0
180
-10 +10dB
40 400Hz
FULL RANGE
CH3 & 4
X1 X10
X1 X10
MO
ST
LP/BP HP
40 400Hz
15 150Hz
40 400Hz
LP/BP
FREQ
SUBSONIC
FREQ
CROSSOVER
PARAMETRIC EQ
-6dB
XXVR-1
DIAGNOSTICS
CLIP
GREEN: POWER
GREEN: PRE-CLIP
AMBER: THERMAL
AMBER: SOFT CLIP
-20dB
0dB
RED: SHORT
RED: HARD CLIP
BASS REMOTE
Channels 3 / 4:
HI PASS: N/A
LOW PASS: N/A
TIP: If you are using the mono sub bass output of an active crossover, there is
nothing wrong with switching in the low pass filter in these amplifiers for a
steeper low pass rolloff.
Level control checklist:
Refer to the section "Setting up systems after installation for best performance"
Minimum final loudspeaker impedances:
2 Ohm per channel in stereo mode.
4 Ohms mono bridged.
PARAMETRIC EQ
CH 1&2
AMPLIFIER
CH1 & 2
PHASE
CUT/BOOST
HIGH PASS
ROUTING
RIGHT
0dB
BANDWIDTH
FREQ
FREQ
HP
CH3&4
X1 X10
X1 X10
FULL RANGE
CH1&2
180
0
180
-10 +10dB
40 400Hz
FULL RANGE
CH3 & 4
X1 X10
X1 X10
MO
ST
LP/BP HP
40 400Hz
15 150Hz
40 400Hz
LP/BP
FREQ
SUBSONIC
FREQ
CROSSOVER
PARAMETRIC EQ
-6dB
XXVR-1
DIAGNOSTICS
CLIP
GREEN: POWER
GREEN: PRE-CLIP
AMBER: THERMAL
AMBER: SOFT CLIP
-20dB
0dB
RED: SHORT
RED: HARD CLIP
BASS REMOTE
SPEAKER OUTPUT
DIAGNOSTICS
RED - SHORT CIRCUIT
BRIDGED
FUSE
AMBER - THERMAL
+
-
+
-
CH1
CH2
RED - CLIP
RED - CLIP
AMBER - NEAR CLIP
AMBER - NEAR CLIP
GREEN - PRE-CLIP
GREEN - PRE-CLIP
CH1 & 2
CH3 & 4
HFR-G1
+
CH3
-
+
CH4
-
REMOTE
BRIDGED
FULL RANGE
SPEAKERS
SPEAKER OUTPUT
DIAGNOSTICS
RED - SHORT CIRCUIT
BRIDGED
FUSE
AMBER - THERMAL
+
-
+
-
CH1
CH2
RED - CLIP
RED - CLIP
AMBER - NEAR CLIP
AMBER - NEAR CLIP
GREEN - PRE-CLIP
GREEN - PRE-CLIP
CH1 & 2
CH3 & 4
HFR-G1
+
-
+
-
CH3
CH4
REMOTE
BRIDGED
+12V
REM
GND
POWER INPUT
CHASSIS GROUND
REMOTE TURN-ON
TO BATTERY + 12V VIA FUSE
+12V
REM
GND
POWER INPUT
CHASSIS GROUND
REMOTE TURN-ON
TO BATTERY + 12V VIA FUSE
7