Hifonics XXV-Sampson Panduan Pengguna - Halaman 12
Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Penguat Hifonics XXV-Sampson. Hifonics XXV-Sampson 20 halaman. Xxv edition high performance amplifier
Halaman Cetak
XXV THOR / XXV CYCLOPS / XXV GOLIATH / XXV SAMPSON MONO AMPLIFIER APPLICATIONS
BASIC APPLICATION
The 1 channel mono amplifiers are capable of 4, 2 & 1 Ohms loads and can be
used in any of the "bi-amplifier" systems described in the XXV-Juno and XXV-Gemini
directions.
SINGLE AMP INSTALLATION PROCEDURE:
1. Connect the amp LINE INPUTS to the Radio/CD player full range or mono line out puts with good
quality RCA interconnect cables.
2. Plug in the XXVR-1 bass remote module into the amp REMOTE INPUT jack.
3. Route a 0 gauge power cables directly to the vehicle battery with an in-line fuse.
FULL RANGE
STEREO LINE INPUT
Y-ADAPTOR
NOT USED
DESIGNATED
MONO
LINE INPUT
-6dB
XXVR-1
DIAGNOSTICS
CLIP
GREEN: POWER
GREEN: PRE-CLIP
AMBER: THERMAL
AMBER: SOFT CLIP
-20dB
0dB
RED: SHORT
RED: HARD CLIP
BASS REMOTE
DUAL AMP INSTALLATION PROCEDURE:
1. Connect the amp LINE INPUTS to the Radio/CD player full range or mono line out puts with good
quality RCA interconnect cables.
2. Plug in the XXVR-1 bass remote module into the amp REMOTE INPUT jack. This will allow the
Master amp to control both Master and Slave amps with just one Bass Remote.
3. Connect an RCA jumper cable from the Master amp MASTER OUTPUT to the Slave amp SLAVE
INPUT. Note: This will "link" the amps so that the Master amp crossover switches will control both the
Master and Slave amps. The Slave amp crossover switches will be bypassed.
4. Route four 0 gauge power cables directly to the vehicle battery with an in-line fuse.
FULL RANGE
STEREO LINE INPUT
Y-ADAPTOR
NOT USED
DESIGNATED MONO
LINE INPUT
-6dB
XXVR-1
DIAGNOSTICS
CLIP
GREEN: POWER
GREEN: PRE-CLIP
AMBER: THERMAL
AMBER: SOFT CLIP
-20dB
0dB
RED: SHORT
RED: HARD CLIP
BASS REMOTE
A SINGLE REMOTE IS CONNECTED TO THE
MASTER AMP IN A LINKED PAIR AND ASSUMES
CONTROL OF BOTH AMPLIFIERS
BASS EQ FUNCTION
10
Note: You can use the Radio/CD designated mono
line output or a full range stereo line output.
For full range stereo line output, you will need an
optional "Y-Adaptor" as shown
Linking two amps for single or dual subwoofer application
Note: You can use the Radio/CD designated mono
line output or a full range stereo line output.
For full range stereo line output, you will need an
optional "Y-Adaptor" as shown
MASTER
SLAVE
4. Connect a 0 gauge ground cables directly to chassis ground with in 36" of the amp.
- Be sure to remove any paint or primer from the ground point.
- Use a nut, bolt and lock washer to secure the ground cable to the chassis ground.
5. Connect the subwoofer(s) in accordance to the diagrams below.
6. Make sure the MASTER/SLAVE switch is in the MASTER position.
Note: The amplifier will not work if the MASTER/SLAVE switch is in the Slave position
CHASSIS GROUND
TO BATTERY +12v VIA FUSE
MONO
SUBWOOFER
REMOTE TURN-ON
TO BATTERY +12v VIA FUSE
CHASSIS GROUND
5. Connect four 0 gauge ground cables directly to chassis ground with in 36" of the amp.
- Be sure to remove any paint or primer from the ground point.
- Use a nut, bolt and lock washer to secure the ground cable to the chassis ground.
6. Make sure the Master amp MASTER/SLAVE switch is in the MASTER position. Make sure the Slave
amp MASTER/SLAVE switch is in the SLAVE position.
7. Connect the subwoofer(s) in accordance to the diagrams below.
8. Connect a 12 gauge jumper from Master amp speaker - to Slave amp speaker - as shown below.
POWER
GND
+12V
REM
+
+
-
-
POWERED BY
MAXXSONICS
SINGLE VOICE COIL
SUBWOOFER
Amplifiers can run at a 2ohm
load minimum when linked
POWER
GND
+12V
REM
+
+
-
-
POWERED BY
MAXXSONICS
+ -
PARALLEL MONO
SUBWOOFERS
2 OHMS EACH MINIMUM
POWER
POWER
GND
+12V
-
-
REM
+
+
+12V
POWERED BY
MAXXSONICS
POWER
POWER
+12V
GND
GND
+12V
REM
+
+
-
-
+12V
POWERED BY
MAXXSONICS
DUAL VOICE COIL
SUBWOOFER
POWER
POWER
+12V
GND
GND
+12V
REM
+
+
-
-
+12V
POWERED BY
MAXXSONICS
+ -
TWO SINGLE COIL
SUBWOOFERS
GND
POWER
GND
POWER
GND