Autonics TZ Series Panduan Produk - Halaman 5

Jelajahi secara online atau unduh pdf Panduan Produk untuk Pengontrol Autonics TZ Series. Autonics TZ Series 6 halaman. Dual pid control temperature controller
Juga untuk Autonics TZ Series: Manual (16 halaman), Manual (16 halaman), Manual (17 halaman), Manual (17 halaman)

Halaman Cetak

Parameter Setting

• Some parameters are activated/deactivated depending on the model or setting of

other parameters. Refer to the descriptions of each item.

• [MD] key: Move to next item after saving / Return to RUN mode after saving (≥ 3 sec)

[◀] key: Select parameter / Move digits / Return to the upper level without saving (≥ 2

sec) / Return to RUN mode without saving (≥ 3 sec)

[▲], [▼] key: Select parameter / Change setting value

• Return to the upper level without saving when there is no key input for more than 30

seconds.

• The range in parentheses '( )' is the setting range when the set value of the 'input

specification' parameter is used with one decimal point.

• Recommended parameter setting sequence: Parameter 2 group → Parameter 1 group

→ SV setting mode

■ Parameter 1 group

Parameter

Display Default Setting range

1-1 SV2 setting

0 Refer to 'Input Type and Using Range'.

SU-2

Event 1 alarm

1-2

10 Refer to 'Input Type and Using Range'.

temperature

AL1

Event 2 alarm

1-3

temperature

AL2

1-4 LBA time

LBA

600

Alarm output

1-5

2 1 to 100 (0.1 to 100.0) ℃/℉

hysteresis

AHYS

Proportional

1-6

#0 0.0 (ON/OFF control) to 100.0%

band

1-7 Integral time

0 0 (OFF) to 3,600 sec

1-8 Derivative time

0 0 (OFF) to 3,600 sec

1-9 Control cycle

1-10 Hysteresis

2 1 to 100 (0.1 to 100.0) ℃/℉

HYS

Input

1-11

0 -49 to 50 (-50.0 to 50.0) ℃/℉

correction

IN-B

1-12 Manual reset

)0 0.0 to 100%

REST

1-13 RAMP up time

RAPU

1-14 RAMP down time

RAPD

1-15 Lock

LOC

OFF

■ Parameter 2 group

Parameter

Display Default Setting range

2-1 Input spec.

KCaH Refer to 'Input Type and Using Range'.

IN-T

2-2 Event 1

EU-1

AL-1

2-3 Event 2

EU-2

AL-2

2-4 Alarm option

AL-T

AL-A

Auto tuning

2-5

mode

AtT

TVN1

2-6 PID type

PIDT

PIdS

Control output

2-7

mode

O-FT

HEAT

Temperature

2-8

?C ℃, ℉

unit

UNIT

2-9 SV high limit

1300 Within input range

H-SC

2-10 SV low limit

L-SC

`00

2-11 Decimal point

0 0, 0.0, 0.00, 0.000

DOT

Transmission

2-12

output high

FS-H

1300

limit

Transmission

2-13

output low

FS-L

`00

limit

2-14 RAMP function

OFF OFF, ON

RAMP

2-15 Comm. speed

BPS

2400

Comm.

2-16

address

ADRS

2-17 Lock

OFF OFF, ON: Parameter 2 group lock

LOC

[Option output 2: Event model]

Refer to 'Input Type and Using Range'.

[Relay, SSR drive output model]

0 to 999 sec

[Relay, SSR drive output model]

1 to 120 sec

• Set to a small value in SSR drive

output models. (e.g. 2 sec)

1 to 99 min

OFF

ON: Parameter 1 group lock

ON1: Parameter 1 group + [AT] key lock

AL-0: Off

AL-1: Deviation high limit alarm

AL-2: Deviation low limit alarm

AL-3: Deviation high, low limit alarm

AL-4: Deviation high, low reverse alarm

AL-5: Absolute value high limit alarm

AL-6: Absolute value low limit alarm

SBA: Sensor break alarm

LBA: Loop break alarm (LBA)

[Option output 2: Event model]

Same as 2-2 Event 1

AL-A: Standard alarm

AL-B: Alarm latch

AL-C: Standby sequence

AL-D: Alarm latch and standby

sequence

TUN1: Tuning based on SV

TUN2: Tuning based on 70% of SV

PID.S: Low speed response

PID.F: High speed response

HEAT: Heating, COOL: Cooling

• Please set according to control

application. Do not change the

settings during operation. It may result

in fire or accidents.

Refer to 'Input Type and Using Range'.

[Option output 2: PV Trans. model]

Within input range

Refer to 'Input Type and Using Range'.

[Option output 2: Comm. model]

2400, 4800, 9600 bps

[Option output 2: Comm. model]

1 to 99

SV2 Setting

It is possible to control an additional temperature value at a desired range by using SV2.

Connect a contact signal (under 5 VDC

the range where the signal turns ON.

The internal temperature of an electric oven may drop rapidly if the door is opened

while the oven is maintaining a specific temperature. Set SV2 to a higher value than SV,

and input a signal to the external terminal (SV2 IN), to quickly raise the temperature.

Temperature

Condition

2-2/3 Event

1/2: AL-1 to 6

RAMP Up/Down Time

2-2/3 Event

1/2: LBA

2-2/3 Event

The ramp function can delay the rate of temperature rise/fall. If the SV value is changed

1/2: AL-1 to 6

during stabilized control, the temperature of the controlled target will rise/fall during

ramp up/down time. The ramp function activates when the power is reset or when the

SV value is changed during stable control.

1-6

Temperature

Proportional

band: ＞ 0.0

Changed SV

1-6

Initial SV

Proportional

band: 0.0

RAMP

time

1-6

Proportional

band: ＞ 0.0

1-7/8

Integral/

derivative

When delaying the rise of initial control temperature or changing the SV during

time: 0

stable control, it is possible to delay temperature rise. Set the ramp up time

2-14 RAMP

longer than the temperature rise time (tu) when not using the ramp function.

function: ON

Temperature

Changed SV

Initial SV

Condition

RAMP

down

time

Delays declining temperature. Set the ramp down time longer than the

temperature decline time (td) when not using the ramp function.

Auto Tuning Mode

2-2/3 Event

Execute auto tuning after select the mode which is suitable for user environment by

1/2: AL-1 to 6

refering to the following desciption.

TUN1

Auto tuning

Temp.

Executes auto tuning based on SV.

2-1 Input

spec. :

Analog

, 250 ㎂) at the external terminal, to operate in

ᜡ

SV 2

External Terminal

(SV2 IN) ON

: Not using ramp function

: Using ramp function

RAMP up time

: Not using ramp function

: Using ramp function

RAMP down time

TUN2

Auto tuning

Temp.

70%

Time

Executes auto tuning based on 70% of SV.

Time