Hifonics BRX1516.1D Panduan Instalasi

Jelajahi secara online atau unduh pdf Panduan Instalasi untuk Penguat Mobil Hifonics BRX1516.1D. Hifonics BRX1516.1D 2 halaman.

Halaman Cetak

Before you start

CAUTION

Many new and factory radios require a reset code when

disconnected from battery power. This is an anti-theft

feature. Before unplugging power, you must determine if

your radio/source unit requires a reset code. Check the

operation manual for your vehicle or contact the dealer.

Model

Power cable size

BRX616.4

and fusing

BRX1616.4

It is critical to use the proper power

BRX5016.5

and ground cable. Select the size

BRX1116.1D

listed here for your amplifier model.

BRX1516.1D

Always use high quality copper

cable. Visit our website for multi amp

system cable recommendations.

BRX2016.1D

Be sure to use the proper fuse size

BRX2416.1D

for each model. Some models require

BRX3016.1D

an external fuse.

BRX4016.1D

Installation

Disconnect

negative battery

terminal

Place terminal in a secure

position so that it won't

accidentally contact the

negative battery post

Run Cables

Properly route power,

speaker and RCA cables

through the vehicle.

Mount Amplifier

Choose a mounting location

that will provide adequate air

ventilation. Mount the amplifier to

a secure surface. Do not mount

the amplifier upside down.

Chassis Ground

The chassis ground connection

is critical to the performance

of the amplifier. Choose a

location that is close to the

amplifier. Completely scrape

away the paint and use a nut

and bolt if possible.

DO NOT USE AN EXISTING

FACTORY BOLT!

Fuse Size

Cable Size

Negative Power

2-35A atc

Connection

3-35A atc

ext - 200A

4ga

Attach the chassis ground

1-80A Maxi

cable to the amplifier

2-70A Maxi

negative terminal. It is

important to make sure this

connection is very tight.

ext - 200A

2ga

ext - 225A

Remote Turn-on

ext - 250A

Connection

ext - 275A

Attach the remote turn on

wire to the amplifier remote

output of the source unit.

Positive Power

Connection

Attach the main power cable

to the amplifier +12V. The

cable must run directly to

the battery and be properly

fused and be very tight.

Signal Input

Connection

Connect the RCA cables to

the INPUT connectors. The

OUTPUT can be used to

provide input for a second

amplifier.

Level Control

Bare metal

BRIDGED

LEFT

RIGHT

SPEAKER

OUTPUT

BRIDGED

LEFT

RIGHT

LEFT

RIGHT

CH 3

CH 4

SPEAKER

OUTPUT

SPEAKER

OUTPUT

SPEAKER

OUTPUT

BRIDGED

LEFT

RIGHT

CH 1

CH 2

SPEAKER

OUTPUT

SPEAKER

OUTPUT

SPEAKER

BRIDGED

CH 3

CH 4

BRIDGED

LEFT

CH1/2

RIGHT

SPEAKER

OUTPUT

Turn the LEVEL control completely

SPEAKER

OUTPUT

counter-clockwise to minimum.

BRIDGED

Speaker

Connections

BRIDGED

CH 3

Connect the speaker cables to

the speaker output connectors.

SPEAKER

Follow the diagram below

that best fits your speaker

configuration.

Stereo

BRIDGED

LEFT

CH1/2

RIGHT

LEFT

CH3/4

LEFT

CH1/2

RIGHT

LEFT

CH3/4

BRIDGED

CH 3

CH 4

SPEAKER

OUTPUT

SPEAKER

OUTPUT

SPEAKER

OUTPUT

SPEAKER

OUTPUT

Monoblock

single woofer

BRIDGED

CH 1

CH 2

OUTPUT

SPEAKER

OUTPUT

SPEAKER

OUTPUT

SPEAKER

OUTPUT

BRIDGED

CH 3

CH 4

Positive Battery

Connection

SPEAKER

OUTPUT

SPEAKER

OUTPUT

Connect the power cable to the

positive battery terminal. The

power cable must be fused

within 18 inches of the battery

terminal.

Be prepared to disarm your vehicle's alarm and

to enter your radio / source unit code.

BRIDGED

LEFT

CH3/4

RIGHT

LEFT

CH3/4

RIGHT

Re-connect

Negative Battery

Terminal

SPEAKER

OUTPUT

SPEAKER

OUTPUT

Re-connect the negative

battery terminal making sure it

is securely tightened.

BRIDGED

CH 4

OUTPUT

Bridged

BRIDGED

RIGHT

BRIDGED

RIGHT

LEFT

CH3/4

RIGHT

LEFT

CH3/4

RIGHT

OUTPUT

SPEAKER

OUTPUT

SPEAKER

OUTPUT

SPEAKER

OUTPUT

Monoblock

multiple woofers

BRIDGED

LEFT

RIGHT

SPEAKER

OUTPUT

SPEAKER

OUTPUT

SPEAKER

OUTPUT

SPEAKER

OUTPUT