Autonics krn100 series Buku Petunjuk

Jelajahi secara online atau unduh pdf Buku Petunjuk untuk Alat Ukur Autonics krn100 series. Autonics krn100 series 2 halaman. 100 mm hybrid recorder
Juga untuk Autonics krn100 series: Buku Petunjuk (2 halaman), Panduan Produk (3 halaman), Manual (17 halaman)

Halaman Cetak

DRW190188AC

100mm Hybrid Recorder

KRN100 SERIES

I N S T R U C T I O N

Thank you for choosing our Autonics product.

Please read the following safety considerations before use.

Safety Considerations

※ Please observe all safety considerations for safe and proper product operation to avoid hazards.

※

symbol represents caution due to special circumstances in which hazards may occur.

Warning

Failure to follow these instructions may result in serious injury or death.

Caution

Failure to follow these instructions may result in personal injury or product damage.

Warning

1. Fail-safe device must be installed when using the unit with machinery that may cause serious injury or substantial

economic loss. (e.g. nuclear power control, medical equipment, ships, vehicles, railways, aircraft, combustion

apparatus, safety equipment, crime/disaster prevention devices, etc.)

Failure to follow this instruction may result in personal injury, economic loss or fire.

2. Do not connect, repair, or inspect the unit while connected to a power source.

Failure to follow this instruction may result in fire or electric shock.

3. Check 'Connections' before wiring.

Failure to follow this instruction may result in fire.

4. Do not touch the product during operation or for a certain period of time after stopping.

Failure to follow this instruction may result in burn or fire.

5. Do not use the unit in the place where flammable/explosive/corrosive gas, high humidity, direct sunlight, radiant heat,

vibration, impact, or salinity may be present.

Failure to follow this instruction may result in explosion or fire.

6. Install on the device panel or DIN rail, and ground to the F.G. terminal separately.

When connecting the F.G. terminal, use AWG16 (1.25mm

Failure to follow this instruction may result in fire or electric shock.

7. Do not disassemble or modify the unit.

Failure to follow this instruction may result in fire or electric shock.

8. Since Lithium battery is embedded in the product, do not disassemble or burn the unit.

Failure to follow this instruction may result in fire.

Caution

1. Use the unit within the rated specifications.

Failure to follow this instruction may result in fire or product damage.

2. Use a dry cloth to clean the unit, and do not use water or organic solvent.

Failure to follow this instruction may result in fire or electric shock.

3. Keep the product away from metal chip, dust, and wire residue which flow into the unit.

Failure to follow this instruction may result in fire or product damage.

4. When connecting the power input or measurement input, use AWG20 (0.50mm²) cable or over and tighten the terminal

screw with a tightening torque of 0.74 to 0.9N . m.

Failure to follow this instruction may result in fire or malfunction due to contact failure.

5. Do not use the load beyond rated switching capacity contact.

Failure to follow this instruction may result in fire, relay broken, contact melt, insulation failure or contact failure.

6. Do not disassemble or assemble input/output card, when power is supplied.

Failure to follow this instruction may result in product damage.

7. Use the transmitter output terminals only as the power for the transmitter.

Failure to follow this instruction may result in product damage.

8. When connecting the temperature sensor(TC, RTD) or analogue input (voltage, current) as input to the universal

input card, set the jumper pin to the correct place for the connected input method.

If the jumper pin is placed improperly, it may result in product damage or malfunc ion.

Specifications

Series

KRN100

Power voltage

100-240VAC

50/60Hz

Allowable voltage range

85 to 110% of rated voltage

Power consumption

Max. 55VA

LCD type

STN Graphic LCD

Resolution

320×120 Pixel

Screen

Adjusting brightness

4-level (OFF/Min/Standard/Max)

Backlight

White LED, 2-level (Temp/Always)

Input channels

2 / 4 / 6 / 8 / 10 / 12-channel (2-channel/card)

Universal input

Temperature sensor (RTD, thermocouple), analog (voltage, current)

1 to 4-channel: 25ms/125ms/250ms, 5 to 12-channel: 125ms/250ms

Sampling cycle

(inner sampling cycle is operation unit time for average movement filter and alarm output function.)

※ Min. sampling cycle for TC-R, U, S, T sensor is 50ms.

Recording speed in graph mode

10, 20, 40, 60, 120, 240mm/H

Recording speed accuracy

F.S. ±0.5%

Storage cycle

1 to 3600 seconds (storage interval time to inner log file is 1 seconds)

Inner memory

512MB

USB memory

※ 1

Recognizes max. 32GB, enables to use cable up to 1.5m

Dielectric voltage

2500VAC 50/60Hz for 1 minute (power terminal and case) ※ Excepts USB Device and Ethernet

Vibration strength

Vibration strength: 10 to 60Hz 4.9m/s

(for convey and storage) and

Opera ing vibration: 10 to 60Hz 1m/s

operating vibration

Insulated resistance

Over 20MΩ (at 500VDC megger)

Noise immunity

±2kV the square wave noise (pulse width 1㎲) by the noise simulator

Time accuracy

Within ±2 min/year (enables to use up to 2100 year)

Enables to normal print with going and returning printing max. 5 times within 7 days after

Ink cartridge

Mech-

opening he unit

anism

Ink dry time

Max. 15 minutes

Protection

IP40 (front panel, IEC Standard)

Recording paper

113mm×9m

Ambient temperature

0 to 50℃, storage : -20 to 60℃ (without ink cartridge)

Environ-

ment

Ambient humidity

35 to 85% RH, storage : 35 to 85% RH

Approval

Weight

※ 2

Approx. 2.4 to 2.7kg (approx. 1.7 to 2.0kg)

※ 1: USB memory is included in the box. If you use USB memory you purchased separately, it could not be recognized.

※ 2: The weight includes packaging. The weight in parentheses is for unit only.

※ Environment resistance is rated at no freezing or condensation.

Dimensions

144

18.6

● Panel cut-out

Min.175

138

1.0

※ Use a steel plate which is 2 to 8mm thickness.

※ The above specifications are subject to change and some models may be discontinued without notice.

※ Be sure to follow cautions written in the instruction manual and the technical descriptions (catalog, website).

M A N U A L

) or over.

(each X, Y, Z axis for 1 hour)

(each X, Y, Z axis for 10 minutes)

137

168

※ This rear side dimension is with

installed I/O cards to every slot.

Connections

This figure is he rear side of KRN100-04000-00-0S.

Slot

Description

1 to 6

Connects universal input card(KRN-UI2).

Connects digital input card(KRN-DI6), alarm output

7 to 10

card(KRN-AR4, KRN-AT6), transmitter power output

card(KRN-24V3).

Connects communication output card(KRN-COM).

l/O Card

Universal input card

[KRN-UI2]

※ Each channel is isolated and dielectric

strength is 500V.

Alarm output card

[KRN-AT6(transistor output)]

Inner

Alarm Output

NPN Open

Collector

12-24VDC/

30mA Max.

RESISTIVE

LOAD

※ AL1,2,3 and AL4,5,6 are isolated.

Screen Layout and Status Display

Screen layout is divided as two; upper screen for status display, lower screen for measuring value display, virtual keyboard display,

parameter setting display.

Upper screen displays recorder status and informa ion of recorder as icon.

Section

Icon

Name

Record start icon

Record stop icon

List record icon

Reservation record icon Flashes during reserva ion recording.

FEED icon

Backup data print icon

Digital mode icon

Graph mode icon

Record memory status

icon

No recording paper icon Marks it for no recording paper. Please replace new recording paper.

USB

(unit: mm)

communication icon

Ethernet communication

icon

RS485 communica ion

icon

Alarm ON icon

Digital input(DI) icon

Digital input(DI)-

memo icon

Digital input(DI)-

alarm reset icon

Digital input(DI)-

start record icon

Digital input(DI)-

stop record icon

Digital input(DI)-

LIST output icon

Digital input(DI)-

record speed icon

Unlock icon

User(general user)

lock icon

Administrator lock icon Marks it for administrator and general user lock status.

Inner and external (USB)

memory capacity icon

Date/Time display

Input Type Setting

Before setting the parameters, set the jumper pin channel 1/2 of

universal input card (KRN-UI2) depending on input specification

as below figure.

SOURCE

Ch1 Jumper

100-240VAC

50/60Hz, 55VA

F.G.

Ch2 Jumper

Jumper

Input

specification

①

0 to 20mA, 4 to 20mA

②

TC, RTD, ±60mV, ±200mV Enables

③

±2V, 1 to 5V, ±5V, -1 to 10V Disables

User Manual

For the detail informa ion and instructions, please refer to user

manual and user manual for communication.

Digital input card

[KRN-DI6]

[KRN-AR4(relay output)]

Inner

Transmitter power output card

Communication output card

[KRN-24V3]

※Each 24V output is isolated individually.

Description

Marks if for starting recording measuring value of recordable channels.

Stops recording measuring value.

Flashes during list recording.

Flashes during feeding recording paper.

Flashes during backup data printing.

Marks it for digital record mode.

Marks it for graph record mode.

Marks it storage capacity of record memory in digital mode or graph mode.

Marks

icon during Modbus RTU communication using USB.

Marks

icon during Modbus TCP communication using Ethernet.

Marks

icon during Modbus RTU communication using RS485.

Marks

channel icon which alarm occurs.

Marks the below icon according to input function setting during digital input (DI).

Marks it when digital memo of digital input or front

status.

Marks it when alarm reset signal of digital input (DI) is input.

Marks it when start record signal of digital input (DI) is input.

Marks it when stop record signal of digital input (DI) is input.

Marks it when LIST output signal of digital input (DI) is input.

Marks it when changing record speed signal of digital input (DI) is input.

Marks it for unlock status.

Marks it for user (general user) lock status.

Displays data capacity of internal memory as bar graph.

Displays current date and time. In summer time season, (S) mark is also

displayed at front of year.

③ ② ①

Terminal

direction

Input break alarm

Enables only 4 to 20mA

Alarm output card

Alarm Output

Relay Contact

250VAC 3A 1a

RESISTIVE LOAD

[KRN-COM]

USB 2 0

(Mini B type)

RS485 A(+)

RS485 B(-)

RS485 S.G

10/100 Base-T

RJ45(Ethernet)

is input in recording