Autopage Car-Pro CPX3500 Petunjuk Pengoperasian

Jelajahi secara online atau unduh pdf Petunjuk Pengoperasian untuk Alarm Mobil Autopage Car-Pro CPX3500. Autopage Car-Pro CPX3500 2 halaman. Professional vehicle security

Halaman Cetak

OPERATION INSTRUCTIONS

REMOTE CONTROL TRANSMITTER OPERATION

Your Car-Pro Security System comes with two 3-button Remote Control

Transmitters that feature a sophisticated code hopping system that will prevent

illegal use of a code grabber with an attempt to record and steal your transmitter

codes.

LOCK – ARM & LOCK

To arm your Security System, press the LOCK button once. The siren will chirp

(1) time and the vehicles parking lights will flash (1) time indicating that the

Security System is now armed. The vehicles doors will lock upon arming when

interfaced with the Security System.

UNLOCK – DISARM & UNLOCK

To disarm your Security System, press the UNLOCK button once. The siren will

chirp (2) times and the vehicles parking lights will flash (2) times indicating that

the Security System is now disarmed. The vehicles doors will unlock upon

disarming when interfaced with the Security System.

DELETING THE ARM/DISARM CHIRP

When attempting to arm or disarm your Security System, you have the option of

temporarily muting the siren chirp sound. To perform this function, simply

depress both LOCK & UNLOCK buttons on the Remote Control Transmitter at

the same time. No chirp sound will be heard, arm / disarm confirmation will be

through the vehicles parking lights only.

VEHICLE LOCATOR

Your Car Pro Vehicle Security System is equipped with a vehicle locator function

which chirps the siren 6 times and flashes the vehicle's parking lights 12 times to

easily locate your vehicle. To access this function, simply press the "Trunk" and

"Unlock" buttons at the same time.

REMOTE PANIC FUNCTION

The Remote Control Transmitter may be used as a remote panic switch that will

activate the Security System's siren and the vehicles parking lights in case of an

emergency. To activate the PANIC function, press and hold the Lock button on

the Remote Control Transmitter for (3) seconds. The siren will sound and the

vehicles parking lights will flash continuously. To cancel the PANIC function,

press the lock or unlock button on the Remote Control Transmitter.

TRUNK RELEASE FUNCTION / PAGER OUTPUT (OPTIONAL

You may use the Trunk button on your Remote Control Transmitter for a

separate function. For example, if your vehicle is equipped with an electronic

trunk release, the Security System can be interfaced with it and can electronically

release your trunk by pressing the Trunk button for 2 seconds on the Remote

Control Transmitter. For additional security you have the option of this output

programmed as vehicle security pager trigger output. Consult with your dealer!

REMOTE CONTROL TRANSMITTER PROGRAMMING

In the event, you should need to add or replace a Remote Control Transmitter, it

is important that you follow the instructions below.

Note:

Each step must be performed within 10 seconds of the previous step

otherwise the system will exit the programming mode.

Enter:

a. Turn the vehicles ignition to the "ON" position

b. Push the valet switch 6 times. There will be 1 long chirp confirmation.

c. You are now ready to program the Remote Control Transmitter(s).

Programming the Remote Control Transmitters:

Press any button on the first transmitter. There will be 1 short chirp.

Within 10 seconds push any button on the second transmitter.

There will be two short chirps confirming

Exit:

a. Turn the vehicles ignition to the "OFF" position, Or

b. Leave for 10 seconds; there will be 3 long chirps to confirm exit.

Note:

The Security System will only retain the last 4 Remote Control

Transmitters programmed. If the Transmitter memory is exceeded, the

Security System will start deleting Transmitters from memory in

chronological order.

CHANGING THE REMOTE CONTROL TRANSMITTER BATTERY

The Remote Control Transmitters come with (1) miniature 12-volt battery. Under

normal use this battery should have a life of approximately one year. If you

should need to replace your battery you may want to return to your installing

dealer. You may also wish to change the battery by yourself. When purchasing

the battery be sure to purchase any of the following: GP23A, #EL12, #VR22 or

Radio Shack #23-144.

To replace the battery, carefully remove the case screw located on the bottom of

the Remote Control Transmitter where the key ring attaches to the case. Use a

miniature #1 Phillips head screwdriver!

After removing the screw, carefully pop open the plastic case. Before removing

the battery note the direction of its "+/-" terminals. Install the new battery exactly

the same way using caution not to bend the battery contacts. Replace the case

cover and insert and tighten the screw. Do not over tighten! Test the Remote

Control Transmitter.

SYSTEM OPERATION

OVERRIDE FUNCTION

The OVERRIDE FUNCTION may be used if the Remote Control Transmitter is

lost or inoperative. To operate, enter the vehicle (alarm will sound), turn the

vehicles ignition to the "ON" position and push the valet/override switch until the

Security System stops sounding. The Security System is disarmed & reset. Have

your Remote Control Transmitter serviced or replaced.

)

VALET FUNCTION

The Security System has a valet or stand-by mode that can be used when the

vehicle is being serviced or valet parked. To activate the valet, turn the vehicles

ignition to the "ON" position, then push and hold the valet / override switch for 2

seconds or until the Security Systems LED turns ON solid. Turn the vehicles

ignition to the "OFF" position; your vehicle is now in valet mode. To reactivate,

repeat the above procedure noting the Security Systems LED will now turn OFF.

Note:

If your vehicle has the Keyless Entry option installed, you can still lock

and unlock the vehicles doors with Remote Control Transmitter while in

the Valet Mode.

PASSIVE/MANUAL OPERATION

Manual Arming / Disarming is controlling your Security Sy stem via the Remote

Control Transmitter. This security system is equipped with an optional Passive

Arming feature, which allows the Security System to arm 30 seconds after the

last door is closed. Operation is as follows.

Turn the vehicles ignition to the "OFF" position and exit the vehicle.

After all entrances are closed, the Security Systems LED will flash fast for

30 seconds. If you re-open any door, the Security Systems LED will stop

flashing. It will begin flashing again once the vehicles door is c losed.

After the 30 second timer has elapsed, the Security System will

automatically "ARM". The siren will chirp (1) time and the vehicles parking

lights will flash (1) time.

Note:

PASSIVE ARMING BYPASS

Your Car-Pro Vehicle Security System can temporarily bypass the Passive

Arming function via the Remote Control Transmitter for one arming cycle. To

temporarily bypass Passive Arming, press the Trunk button twice before exiting

the vehicle. The Security System will confirm with 1 short chirp. Passive

operation will be restored once the Security System is armed by the Remote

Control Transmitter.

PRIORITY UNLOCK (OPTIONAL)

Your AutoPage Security System is equipped with a priority door unlock feature

which will independently unlock the drivers door only when disarming the

Security System. Pushing the Unlock button a second time within 3 seconds will

unlock the entire vehicle. This feature requires additional installation and is not a

standard feature of the Security System.

AUTOMATIC REARMING (OPTIONAL)

If this feature is selected, the Security System will automatically re-arm itself 60

seconds after disarming with the Remote Control Transmitter. Automatic rearm

will cancel if any door is opened before the 60 second timer has elapsed.

IGNITION CONTROL DOOR LOCKS (OPTIONAL)

If the vehicles door locks have been interfaced to the Security System, the

Security System will automatically lock the vehicles doors when the ignition is

turned "ON" and/or unlock the vehicles doors when the ignition is turned "OFF".

Note:

LED STATUS INDICATOR

LED OFF: Security System is disarmed

LED ON: Security System is in valet mode

LED FAST FLASHING: Automatic arming timer is counting down

LED FLASHING: Security System is armed

LED FLASHING AFTER DISARMING: Security System Violation

If the vehicles door locks have been interfaced to the Security System,

the vehicles doors will automatically lock after the passive arming cycle

has been completed. If this feature is not desired, see your local

dealer and have the Security System re-programmed to eliminate

passive door locking.

If any door is open when the ignition is turned "ON", the Security

System will not automatically lock the vehicles doors.

2 Flashes...pause- Trunk / Hood Violation

3 Flashes...pause- Door Trigger Violation