Autopage MA-200 Panduan Pengoperasian - Halaman 5

Jelajahi secara online atau unduh pdf Panduan Pengoperasian untuk Sistem Keamanan Autopage MA-200. Autopage MA-200 13 halaman. 2-way remote control motorcycle alarm
Juga untuk Autopage MA-200: Panduan Petunjuk Instalasi (8 halaman)

3. After the 30-second timer has elapsed, the security system will automatically "ARM". The siren will chirp
[1] time and the parking lights will flash [1] time.
PASSIVE ARMING BY-PASS: While the system is disarmed, press the
the security will respond with [1] chirp and LED will turn "ON". The security system will remain in this
temporary state for as long as you wish. To exit passive by-pass, press the
the system will return to normal status.
I. ACTIVE DISARMING –
1. Press the
button on the transmitter.
2. The siren will chirp twice and parking lights will flash twice to indicating that the security system is now
disarmed.
Activated on the
System Disarm
Tilt Sensor
(Optional)
Clearing the Flashing Icons: Pressing the
icons on the LCD screen transceiver.
SILENT DISARMING: Press the
security system. No chirp sound will be heard. Disarm confirmation will be through the motorcycles parking
lights only.
TAMPER DISARMING: If alarm has been triggered. Upon disarming the system the siren will chirp 4 times
and the parking lights will flash 3 times.
DISARMING WITH PATHWAY ILLUMINATION: Press the
will chirp once. Within 3 seconds, press
illuminate your pathway.
AUTOMATIC RE-ARM: If this feature is selected, the security system will automatically re-arm itself 60
seconds after disarming with remote transmitter. Pressing the
on the ignition switch will cancel the rearm.
J. DISARMING WITHOUT A TRANSMITTER
OVERRIDE THE ALARM WITHOUT PASSWORD PIN CODE: (Factory Default Setting)
The Override function may be used if the remote transmitter is lost or inoperative.
1. Turn the ignition switch to 'ON' position. (Alarm will sound.)
2. Within 10 seconds push and release the valet switch
The alarm will stop sounding and will enter the disarm mode. You can now start and operate the
motorcycle normally.
OVERRIDE THE ALARM WITH PASSWORD PIN CODE:
Since the valet switch can be easily found and defeated, this security system allows the consumer to
program a password pin code offering a higher level of security.
1. Turn the ignition switch to the 'ON' position. (Alarm will sound.)
2. Press the Valet switch the selected number of times (1-9 presses) within 15 seconds.
(By pressing the Valet switch the system's siren will stop alarming and the parking lights will stop
flashing but the motorcycle cannot be started and driven away until you disarm the system.)
The system should now be disarmed. If it is not, you may have waited too long to press the Valet switch;
turn the ignition off and on and try again.
K. VALET MODE:
(System in Disarm or Valet mode)
The valet switch allows you to temporarily bypass all alarm function, eliminating the need to hand your
transmitter to parking attendants or garage mechanics. When the system is in valet mode, all alarm
function are bypassed, however the remote panic feature and Channel 3 /4 will remain operational. To
use the valet mode, the system must first be disarmed either by using your remote transmitter, or by
operating the Manual override sequence.
MA-200 OP REV.A
Activated on the
Activated on the
Close Loop
Shock Sensor
button 3 times within 3 seconds will clear the flashing
F
button first, within 3 seconds press
button once to disarm the system, the siren
F
button. The parking lights will be turned "ON" for 30 seconds to
F
button twice within 3 seconds or turning
5
Oct/23/2006
F
button twice within 3 seconds,
button or
button and
Activated on the
Ignition Switch
button to silently disarm your