Galletti Estro SMRC Manual - Halaman 3

Jelajahi secara online atau unduh pdf Manual untuk Kipas angin Galletti Estro SMRC. Galletti Estro SMRC 17 halaman. Outdoor air inlet motorized louver

Halaman Cetak

This louver is intended for replacing the air in the room directly from the

G B

fan coil unit.

The amount of outdoor air, filtered and treated thermally, may be regulated

proportionally from 0 to 100% by means of a built-in servomotor.

The SM kit, as shown in figure 1, essentially comprises the following components:

Outdoor air inlet louvre made of steel sheet painted in the same color as

the cover cabinet.

Servomotor connected directly to the louvre's baffle, with a protection rating

of IP54 and power supply of ~ 24V.

The louvre may be opened or closed automatically at the signal of the external

auxiliary contacts (not supplied) such as antifreeze thermostats, timers,

etc., with the possibility of connecting multi-servomotors in parallel to an

individual position transducer.

230V - 24V voltage transformer, complete with support terminal strip.

Self-threading screws 4.2 x 13 for fixing the fan coil unit to the basic unit.

The control panels (accessories CSB and CSD), which activate the servocontrol,

are envisaged both for being installed on-board the fan coil unit and for the

remote installation (flush wall-mounting). They open or close the louver from

0 to 100%.

One of the following control panels must be coupled to the louvre:

Panels

code

Control on-board the machine for the proportional opening and closing of the SM

EYCSB

motorized louvre

Flush wall-mounting control for the proportional opening and closing of the SM

EYCSD

motorized louvre

To prevent the water from freezing inside the heat exchanger during the winter,

close the outdoor air inlet when the system is not operational or use an

antifreeze solution checking its freezing point.

% of glycol in weight

Freezing point (°C)

The kit may be installed on the whole range of the éstro series fan coil units.

INSTALLATION

1. Check that the desired installation complies with one of the configurations in

figure 2.

Flush-mounted fan coil unit with 90° air inlet louver;

Flush-mounted fan coil unit with in-line air inlet louver;

Ceiling-mounted fan coil unit with 90° air inlet louver;

Ceiling-mounted fan coil unit with in-line air inlet louver.The outdoor air

inlet louver is always supplied with the sleeve in the back air inlet position.

2. Remove the sleeve as shown in figure 3.

3. Make an opening in the wall complying with the sizes shown in figure 4.

Note: As a rule the outdoor air inlet louvre is coupled with the outdoor air inlet

grid (GE+C).

To limit flow resistance of the sucked outdoor air, it is advisable to create the

opening as shown in figure 5.

4. Insert the sleeve into the opening and fix it as shown in figure 6 based on the

type of chosen installation.

Flush-mounted fan coil unit with 90° air inlet louver;

Flush-mounted fan coil unit with in-line air inlet louver;

Ceiling-mounted fan coil unit with 90° air inlet louver;

Ceiling-mounted fan coil unit with in-line air inlet louver.

5. Reassemble the sleeve on the louver, remove the cover cabinet from the fan

coil unit, connect the basic unit to the louvre (figure 7) and fix the basic unit to

the wall using 4 anchor screws.

6. Install the control panel (accessory CSB or CSD, figure 8b), on-board or

remotely or flush-mounted as shown in figure 8a.

7. Make the electrical connections complying with the diagrams of figure 9a (SMR

- SML), 9b (SMRC - SMRL), depending on the type of SM you have chosen.

Make the electrical connections, with power OFF, conforming to the prevailing

safety regulations.

Each fan-coil requires a switch (IL) on the feeder line with a distance of at least

3 mm between the opening contacts, and a suitable safety fuse (F).

The installer is in charge of carrying out the hatched connections.

The transformer is not supplied as a standard fitting for louvres setup for

the centralized control.

In these cases, provide a 24V-power supply line by sizing the transformer

according to the number of expected louvers. Consumption of every single

servomotor: 5 VA.

The SM louvers may be connected in parallel to a unique control up to a

maximum of 10.

È severamente vietata la riproduzione anche parziale di questo manuale / All copying, even partial, of this manual is strictly forbidden

Panels description

-4

-10

-16

The following abbreviations are used in the diagrams:

- Position transducer (control), built-in or remote

- Protection fuse

- Line circuit breaker

DB-DMN24

- Louver servomotor

- Supplied transformer

- Transformer for centralized 24V line

A, B

- Auxiliary contacts (antifreeze thermostat, etc.):

A open + B open = 0%,

A closed + B open = 0 - 100%

A closed + B closed = 100%

A open + B closed = 100%

- Fan coil unit power supply line

- Connection to the position transducer, cable cross-section 1.5 mm

- Power supply of the following motors (10 at the most)

Black

Blue

Brown

Grey

8. If installed on fan coil units fitted with a cabinet (FL, FA and FU), a pair of covering

bases must be coupled to the louver, as outlined in the table below:

Covering base Covering base description

code

EYZA1

ZA1 pair of covering bases F1-9 A

EYZA10

ZA10 pair of covering bases models F10-12 A

EYZL1

ZL1 pair of covering bases F1-9

-24

EYZL10

ZL10 pair of covering bases models F10-12 L

OPERATION

The louver is operated by the control panel that contains the position transducer

that regulates the opening of the louvre in proportional mode.

On setting the control (100% for the remote control panels) the position of the

louver is that of total outdoor air inlet. Vice versa on setting the control (0% for

the remote control panels) the position of the louver is that of total ambient air

recycle.

The serigraphy on the control panel indicates the percentage of the fresh air.

CLEANING OF THE AIR FILTER

When removing the air filter for the periodic cleaning operations, the position

of the baffle should be that of total ambient air recycle (0%).

HOW TO PLACE YOUR ORDER

In order to properly identify the outdoor air inlet louvre, carefully read what

is stated below.

The servomotor should always be positioned on the side opposite the

hydraulic couplings of the heat exchanger that operates with cooled water:

choose the louver with the motor on the right or on the left, accordingly.

For fan coil units with the DF supplemental 1-row heat exchanger, always

adopt the remote control panel.

If the SM louver is coupled to ceiling-mounted equipment with the FU version

cabinet, the fan coil units are to be ordered indicating the "with blind panel"

description.

The motorized louver kits designed for serving more than one motor to a

unique control (centralized control) are not equipped with the voltage

transformer. For further information refer to the wiring diagrams.

Models

F1-F4

F5-F6

SMR

EYSM1R

EYSM5R

SML

EYSM1L

EYSM5L

SMRC

EYSM1RC

EYSM5RC

SMLC

EYSM1LC

EYSM5LC

LEGEND:

SMR:

Motorized louver, motor on the right, with transformer

SML:

Motorized louver, motor on the left, with transformer

SMRC: Motorized louver, motor on the right, for centralized control

SMLC: Motorized louver, motor on the left, for centralized control

F7-F9

F95

F10-F11

EYSM7R

EYSM95R

EYSM10R

EYSM7L

EYSM95L

EYSM10L

EYSM7RC EYSM95RC EYSM10RC EYSM12RC

EYSM7LC EYSM95LC EYSM10LC EYSM12LC

FC66000720 - rev. 01

Version

F12

EYSM12R

EYSM12L