ADESCO MQ03-4I Panduan Instalasi & Konfigurasi - Halaman 4

Jelajahi secara online atau unduh pdf Panduan Instalasi & Konfigurasi untuk Ponsel ADESCO MQ03-4I. ADESCO MQ03-4I 11 halaman. Global sim universal communicators

Halaman Cetak

End-user smartphone app – supports push notiﬁcations, arming/disarming of the alarm system, video veriﬁcation.

Diﬀerent options to connect to alarm panels

The MQ03 communicators can receive events from any alarm panel via digital inputs, via telephone line communicator, or serial port, as follows:

The digital inputs of MQ03 are pulled-up and activated by GND. Custom messages can be assigned to each edge of the input signal.

The Device can emulate telephone line and can decode the DTMF signals from the telephone line communicator of the alarm panel.

This is another universal way to integrate with any alarm panel and to retrieve extended information about partitions, zones and

users.

MQ03 communicators can also integrate with some alarm panels via the serial port. This feature gives the possibility for bi-directional

communication and remote programming of the panel with the manufacturer's programming software.

Device Installation guide

The Device can be installed in a metal or non-ﬂammable plastic enclosure together with an alarm system unit. When the metal enclosure is used

it is recommended to ground the enclosure using 0.50 mm

1 thread cable of up to 100 meters length.

Mounting

Connect the GSM antenna to SMA connector. Check if the antenna is ﬁxed properly. It is not recommended to turn on the device without GSM

antenna connected. Warning: It is recommended to install the GSM antenna away from the alarm system to ensure better quality of the signal.

It is not recommended to install the antenna inside the metal enclosure.

2. Connect the Device to the alarm panel according to the desired communication method (see

power supply is suﬃcient for the load of the module. The quiescent current of the module is up to 150mA, however it can reach up to 400mA

during communication. Warning: Power supply at alarm system must be disconnected before any installation or maintenance work.

3. Now the Device can be powered up. It should start in less than a minute. The GSM LED indicator should be ON indicating successful connection

to GSM network. LED indicator meaning:

Oﬀ - the device is switched oﬀ

Slow ﬂashing (once per second) - no connection to a server (CIS)

On - the device is connected to a server without data transfer

Fast ﬂashing – data transfer

5. Check the GSM signal strength through the administrative web site or administrative mobile application. It may happen that the signal

strength is not suﬃcient in the desired mounting place. In this case the planned installation place can be changed before mounting the device.

Signal levels below 10 are unacceptable. Recommended levels are above 14.

Warning: Do not mount the Device in places where it can be aﬀected by strong electromagnetic disturbances (e.g. in the vicinity of electric

motors, etc.). Do not mount the Device in wet places or places with high degree of humidity.

Conﬁguration of terminals of MQ03-4I-DTMF GPRS Communicator

Terminals description:

IN1 – IN4: digital inputs, triggered by ground (-), pulled-up with 2.2KΩ to 5V

OUT1 and OUT2: open collector outputs

RING and TIP: connect to the RING and TIP of alarm panel

RX and TX: serial interface TTL (4V)

Device Conﬁguration Guide

Your administrative tools – web site and mobile application

Generally, devices will be shipped preconﬁgured according to the needs of each client. To request changes of your default settings, please

contact your account manager.

In most cases, when you install a device on site you will only need to wire it and conﬁgure the Site Number.

Most of the conﬁguration you would need to perform in your everyday routine as an installer or administrator could be performed via the

administrative mobile application for Android smartphones that you can download from here:

https://play.google.com/store/apps/details?id=m2m.AdminMobile

The mobile application is designed to allow easy conﬁguration via 3G and WIFI when you are on the move.

You can also change the settings from the administrative web site:

Some of the settings that are seldom changed can be conﬁgure ONLY via the administrative web site.

Most frequently used scenarios

This chapter describes some of the most frequently used administrative scenarios. You can ﬁnd the detailed description of the administrative site

features in the chapters that follow after.

Conﬁguring a new device via a template

It is recommended that the device is powered and is connected to the server (Connected = True). This will enable you to check and

save all available settings, including the online settings.

GSM/GPRS Communicator MQ03 User Manual Version 1.1

1 thread cable. For the device connection to input/output connectors use 0.50 mm

(RControl Admin current)

https://m2m.adesco.gr/admin

Configuration of

Terminals). Make sure that

page 4 of 11