KitchenAid 4KSRF42DT Panduan Petunjuk Instalasi - Halaman 7

Jelajahi secara online atau unduh pdf Panduan Petunjuk Instalasi untuk Kulkas KitchenAid 4KSRF42DT. KitchenAid 4KSRF42DT 12 halaman. 42” (1067 mm) built-in refrigerator

Halaman Cetak

Electrical

requirements

Electrlcal Shock Hazard

Improper connectlon of the

equlpment-groundlng

conductor can result In a rlsk

of electrical shock. Check

wlth a quallfled electrictan or

service technlclan

If you are

in doubt as to whether the

appliance Is properly

grounded.

Do Not use an extenslon cord

wlth thls appliance. Such use

may result In a fire, electrlcal

shock, or other personal

Injury.

120-volt, 60-Hz, AC only, 15-or 20-

ampere, fused, electrical supply is

required. A time-delay fuse or circuit

breaker is recommended. It is

recommended that a separate circuit

serving only this appliance be

provided.

Recommended grounding

met hod

DO NOT, UNDER ANY

CIRCUMSTANCES, REMOVE THE

POWER SUPPLY CORD GROUNDING

PRONG.

For your personal safety, this

appliance must be grounded. This

appliance is equipped with a power

supply cord having a 3-prong

grounding plug. To minimize

possible shock hazard, the cord

must be plugged into a mating

3-prong, grounding-type wall

receptacle, grounded in accordance

withliocai codes and ordinances.

See Figure 1. If a mating wall

receptacle is not available, it is the

personal responsibility and

obligation of the customer to have a

properly grounded, 3-prong wall

receptacle installed by a qualified

electrician.

Water supply

requirements

Use only 114" (6 mm) copper

tublng for water Ilne.

The water line to the refrigerator

must provide 15-100 psi (103.5 -

690 kPa) water pressure.

The preferred method of installing

the plumbing to the refrigerator is

through the wall. An optional

method is installing the water line

through a floor opening. If the

copper tubing is installed through

the floor, the hole cut in the floor

must be angled 45O toward the front.

You will need enough

l/4" (6 mm) -

copper tubing to connect from water

line to refrigerator, a saddle-type

valve and a union. Rough in the

water line before installing the

refrigerator. See steps that follow.

Product/Properly

Damage Hazard

Do Not Install copper tublng

In an area where temperatures

drop below freezlng.

To do so may result In water

damage.

.Find a 3/8" (9 mm) to 1" (25 mm)

vertical cold water line near the

refrigerator. Measure the

distance from the cold water line

to the refrigerator location. Add

24 inches (610 mm) for the final

length of copper

tubing you will

need. Cut both

ends of copper

tubing square.

2.Tum off

main water

supply and

clear water

line.

Electric Shock Hazard.

Eiectrlc drill must be grounded

to prevent severe or lethal

shock If water is in line and

enters drill during use.

Fallure to ground drill may

result In personal Injury.

Ground electric drill or use a hand

drill. Drill a 3/16" (5 mm) hole in

vertical cold water line. Attach a

saddle valve to the water line with

a clamp in an easily accessible

location. Insert a washer

between clamp and line. Check

that inlet end is solidly in the drill

hole. lighten packing nut.

Tighten the pipe clamp screws

evenly so washer makes a

watertight connection. Do Not

overtighten or copper tubing

could be crushed.

4. Slide compression nut and sleeve

on copper tubing. insert end of

copper tubing completely into

the outlet valve. Tighten

compression nut to outlet with an

adjustable wrench. Do Not

overtighten. Turn on main water

supply and flush copper tubing.

Turn the new water line valve to

the "OFF" position.

5. Route copper tubing to the

refrigerator location.

Slide

compression

nut and sleeve

over water line.

Connect union

to compression

nut and sleeve.

Tighten with

adjustable wrench.

Do Not

over-lighten.

Page 6