Adesso Espresso 690008101 Panduan Pengguna - Halaman 7
Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Pembuat Kopi Adesso Espresso 690008101. Adesso Espresso 690008101 8 halaman. Espresso coffee machine
Halaman CetakUSER'S MANUAL
CAUTION
!
If you turn on 180 grades the cup grid (fig. 1, ref. 8), you will
suite the level to use the coffee delivery spout for express cup
or the cappuccino cup, as you need.
No water
If you turn on the machine with the tank empty, THAT COULD
11
DAMAGE THE MACHINE.
The no water inside the tank is signalled:
1) By the different noise of the pump;
2) By the difficulty or impossibility to delivery water and/or cof f ee.
In this case please turn off the machine and proceed immediately
to refill the tank (fig. 3, ref. C).
MAINTENANCE
Washing
a) Place a cup or a glass on the plate of cup grid under the delivery
switch;
b) Open the capsule insertion door (fig. 1, ref. 1);
c) Place one of the empty capsules supplied with the machine
inside the proper opening (fig. 1, ref. 4);
d) Close the capsule insertion door completely (fig. 1, ref. 1);
e) Put the coffee push-button (fig. 1, ref. 7) on the position I and
wait for the end of the delivery (about 2 minutes);
f) Put the coffee push-button (fig. 1, ref. 7) on the position 0;
g) Emptying the cup. The empty capsule remains inside
the machine until the new capsule is inserted.
h) Remember to remove it from the used capsule collection drawer
in order to use it again for future machine cleaning.
Tank refilling
Check and, if it is necessary, refill the tank, please follow
the instructions and the advices specified.
Drawer emptying
Every new capsule allows the used capsule to fall into the drawer
(fig. 1, ref. 9), that must be emptied periodically at least every 30
drinks delivered.
CAUTION
!
If the drawer is not emptied, the capsules can jam inside the
machine and block it completely.
Cleaning
CAUTION
!
To clean the machine's parts don't use the dishwasher.
THAT WILL CAUSE COMPLETE DAMAGE OF THE MACHINE.
Drawer cleaning
The drawer can be cleaned with water . Don't use detergents,
products or abrasive material that could damage the drawer .
Outer parts cleaning
Clean the outer parts of the machine using a damp cloth only .
Don't use products or abrasive materials that could damage the
machine surfaces.
Tank cleaning
Periodically, approx. every 10 liters of water used or even more
frequently if using hard water or water with impurities, it is
necessary to clean the water tank, Then:
1. Remove the access lid (fig. 3, ref. A);
2. Remove the two water pipes from the holes on the tank
(fig. 3, ref. B);
3. Remove the tank from its housing (fig. 3, ref. C) and wash it
internally with running water;
4. Fill up the tank and dry the tank outer sides with car e ;
5. Place the tank into its housing;
6. Insert the two water pipes into the holes on the tank (fig. 3, r e f. B);
7. Close the tank access lid (fig. 3, ref. A).
Model with descaling filter (not included)
a) Remove the suction pipe complete with descaling filter from the
tank opening and the recovery pipe from the hole on the tank
(fig. 3, ref. B) (descaling filter supply);
b) Insert the suction pipe complete with descaling filter into the
tank opening and the recovery pipe into the hole on the tank
(fig. 3, ref. B) (descaling filter supply).
Descaling
Standard
Periodically, approx. every 50 liters of water used or even more
frequently if using hard water than 25°F it is necessary to perform
a washing cycle using a descaling product specifically designed for
espresso coffee following the instruction provided with the product.
Descaling filter
Periodically, approx. every 50 liters of water used or even more
frequently if using hard water than 25°F it is necessary to replace
the descaling filter following the instruction provided with the filter
(enclosed).
Replacement of the light bulb
To replace the incandescent light bulb when it gets burnt, follow
the instructions below:
1. Turn off the coffee machine and disconnect the plug;
2. Remove the frontal cup grid by pressing lightly on each of its
support points until the frontal cup grid pulls out;
3. Move the frontal cup grid and the glazed pipe away enough to
have the light bulb free;
4. Unscrew and replace the light bulb with another one with the
same specifications;
5. Set the glazed pipe in its position (in front of the cup grid);
6. Put the frontal cup grid in the right position, matching its
12