JADO Classic 853/131 Series Petunjuk Instalasi - Halaman 2

Jelajahi secara online atau unduh pdf Petunjuk Instalasi untuk Perlengkapan Dapur & Kamar Mandi JADO Classic 853/131 Series. JADO Classic 853/131 Series 2 halaman. Pressure balanced shower valve with check stops and trim

Halaman Cetak

TOOLS REQUIRED

Channel Locks

Tubing Cutter

Adjustable Wrench

ROUGHING-IN DIMENSIONS

To assure proper positioning in relation to wall,

note roughing-in dimensions.

1-5/8" TO 3-1/4"

FINISHED WALL

1/2" NPT

OPTIONAL TO

FINISHED FLOOR

USUALLY BETWEEN

72'' AND 84"

"SEE ILLUSTRATION"

SHW

7-7/8"

TUB

48" TO 54"

OPTIONAL

1/2" PLUG

BOTTOM OF

TUB

OR SHOWER

STALL

ROUGHING-IN

CAUTION

Turn off water at main supply.

NOTE

When soldering, remove PLASTER GUARD, CARTRIDGES and CHECK

STOPS (IF PRESENT). When finished soldering, flush valve body, replace

cartridges, check stops (if present) and plaster guard to continue installation.

Use thread sealant or Teflon tape on threaded connections.

See Roughing-in diagram before starting.

Connections are:

1/2" female NPT for threaded inlets

Connect RISER PIPE (1) to MANIFOLD (2)

top outlet marked "SHR".

Plug TUB outlet with 1/2" NPT PLUG supplied.

For proper positioning the finished wall

must be within side wall of PLASTER

GUARD (4).

If the valve is installed on a fiberglass or

other thin wall application, the PLASTER

GUARD (4) can be used as a support.

Cut a 4" dia. hole in the shower stall.

Drill two additional 1" holes to allow

access to the stops.

Remove PLASTER GUARD (4), rotate

180˚ so that indicated screw holes fit

MANIFOLD (2). Push CAP on valve, place

ESCUTCHEON on and attach with screws.

Connect hot and cold water supplies.

Cap off shower pipe (5).

For support, use pipe BRACES (6) secured to wooden braces.

With valve turned off, turn on water supplies. Check for leaks.

Phillips Screwdriver

Teflon Tape

Plumbers' Putty or Caulking

INLETS 1/2" NPT

5-7/8"

OUTLETS 1/2" NPT

3-3/8"

THREADED INLETS (STOPS)

COLD

HOT

PLUG

INSTALL TRIM

Push CAP (1) onto VALVE CARTRIDGE (2). Secure CAP (1) to

VALVE CARTRIDGE (2) with SCREW (3) for LEVER HANDLE only.

(Spline in CAP (1) must fully engage spline on cartridge stem).

Mount ESCUTCHEON (5) with gasket to valve body and secure

Regular Screwdriver

with SCREWS (6).

Push the COVER (7) as shown over the CAP (1) and align

prongs on COVER (7) with screw holes in ESCUTCHEON (5).

Important! Make sure COVER (7) snaps over the SCREWS (6).

INSTALL HANDLE (ADJUST HOT LIMIT STOP

PRIOR TO HANDLE INSTALLATION,

SEE STEP 3)

For Cross Handle: Thread HANDLE BASE (8) onto

threads of CAP (1) until seated against it's internal

stop. With VALVE in off position align CROSS

HANDLE (9) as desired. Install CROSS HANDLE (9)

onto VALVE STEM (15) and tighten HANDLE

SCREW (10). Thread INDEX (11) into

CROSS HANDLE (9).

Lever Handles: Thread HANDLE BASE (4) onto

threads of CAP (1) until seated against it's internal

stop. Install FRICTION WASHER (14) onto base

of LEVER HANDLE (12). Align LEVER HANDLE (12)

and tighten set screw with HEX WRENCH (13)

supplied with faucet to secure handle.

ADJUST HOT LIMIT STOP (MUST BE DONE PRIOR TO TRIM INSTALLATION)

By restricting HANDLE rotation and limiting the amount of hot water allowed to mix with the cold, the

HOT LIMIT SAFETY STOP (1) reduces risk of accidental scalding. To set the maximum hot water

temperature of your faucet, all you need to do is adjust the setting on the HOT LIMIT SAFETY STOP (1).

Remove Handle Assembly and Trim. See above step 2 for reference.

Turn CARTRIDGE STEM (2) to the OFF position (coldest setting) before making adjustment to HOT

LIMIT STOP (1). Use a flat blade screwdriver to pry free the HOT LIMIT SAFETY STOP (1). Pull

forward and rotate counterclockwise one number to limit hot water temperature.

Use ARROW (3) on CARTRIDGE (4) and NUMBERS (5) on HOT LIMIT STOP (1)

for indication.

1 0 9 4 9 2 A

CAUTION

Turn off water at main supply.

LEVER HANDLES

COLDER

(Larger Numbers)

0 1 3 5 7 9 11 13 15

THREADS

ON CAP

CROSS HANDLE

HOTTER

(Smaller Numbers)

0 1 3 5 7 9 11 13 15

1 0 9 4 9 2 A