IKEA Akurum kitchen Panduan Instalasi - Halaman 12

Jelajahi secara online atau unduh pdf Panduan Instalasi untuk Perabotan Dalam Ruangan IKEA Akurum kitchen. IKEA Akurum kitchen 17 halaman. Kitchen

Halaman Cetak

Hang these

instructions on

the wall so you'll

have your

hands free

AKURUM

wall cabinets are mounted

using a sturdy steel suspension rail. This

ensures a strong installation, and makes

it easier to hang and level the cabinets.

If you haven't already done so in Step 1,

measure and draw the position of the cab-

inets on the wall to ensure that everything

will fit. Also be sure you've marked uneven

and high spots on the wall.

1. Checking for uneven spots

2. Next

Start by

checking the walls visually

Check the floor to find its high point.

and running a 4 foot level along the

The level will help you here as well.

surface. Mark any irregularities, such

Check all areas where you'll be

as bows and high spots. If major prob-

installing base or high cabinets, and

lems need to be fixed, you may want

mark the high and low points on the

to hire a professional. It may also be

wall.

necessary to use shims when mount-

ing the cabinets.

6. Cut the suspension rail

Measure the length of the

wall cabinets

Slide the suspension rail

to be installed along one wall. Include

the suspension rail before putting it up.

the length of wall behind a high cabinet

You'll need two pieces per wall cabinet.

only if the high cabinet is 12" deep.

(Be sure to position one piece on each

Subtract

" from the overall measure-

side of the corner cabinet if your plan

ment. (This will leave

" of space at

calls for one.) You may find it helpful to

either end of the rail.) Use your hack

tape the hardware into place until the

saw to cut the suspension rail to this

rail goes up.

length.

11. Hang the remaining

12. Drill

wall cabinets

You'll find predrilled holes on the inside

Hang the rest of the cabinets in the

of each cabinet. For all doors except

same way, aligning each with the previ-

ULRIKSDAL use a

ous one. Use your clamps to temporarily

through the fourth holes from the top

hold adjacent cabinets into position. To

and bottom edges. (The second and

avoid marring the surface of your cabi-

third holes are for the door hinges.) For

nets, use a small scrap of wood between

ULRIKSDAL door, drill through the

the clamp and the cabinet.

second holes from the top and bottom

edges. (The hinges for ULRIKSDAL fit

into the third and fourth holes from the

top/bottom.)

Step 3. Hang the wall cabinets

When you've completed Step 3,

3. Finally

Fit a combination square or right

angled wood panel into each corner,

and see if there are any gaps between

it and the wall. If the gap is more than

", call your IKEA expert for assis-

tance. In a "U" shaped kitchen, meas-

ure between opposite walls at a num-

ber of spots to see if they are parallel.

Insert suspension rail hardware

8. Secure the suspension rail

hardware into

Secure the suspension rail to the

aligning the bottom edge of the rail

with the level line marked on the wall.

If you found a bow in the wall of more

than

rail until it is straight. Should the end

of the rail fall between studs, secure it

to the wall with a heavy duty anchor.

through cabinet walls

13. Fasten cabinets together

Place the connection screws

with the cabinet frames into the holes

" drill bit to drill

and tighten. Remove the clamps.

Continue fastening the remaining cabi-

nets together in the same way.

all of the wall cabinets will be in place.

4. Mark the level lines for the wall

cabinets and suspension rail

Using the high point on the floor that

you marked in Step 1, measure up the

wall 83

or 92

locate the bottom of the suspension rail

by measuring down 2

tal cabinets) from the first mark. Then

draw level lines on the wall.

9. Hang the corner cabinet

studs,

Starting with the corner cabinet,

one piece of the suspension rail hard-

ware with the predrilled hole at the top

of the cabinet. Position the second hole

" in Step 1, shim the suspension

and its hardware. Note: If you don't

have a corner cabinet, install a cabinet

that fits against both the back and side

walls, allowing the filler space shown

on your plan.

14. Tighten the mounting screws

enclosed

When all

mounted, aligned and connected, and

final adjustments have been made,

tighten all of the mounting hardware.

Slide the plastic covers in place over

the metal corner bracket.

5. Finding the studs in

At the marked suspension rail

the wall from the corner out (or use a

stud-finder) to check for the first stud.

" for the top of 30" wall cabinets

Mark its position. While subsequent

" for 39" wall cabinets. Next,

studs are usually at 16" intervals, they

may be at 12" or 24" intervals in some

" (3" for horizon-

kitchens. Mark the location of each stud

along the line. This will show you where

to attach the suspension rail to the wall.

10. Level and secure the cabinet

align

Fit the small metal plate over the bolt,

thread the nut loosely in place. Level

the cabinet, using shims at the bottom

edge if necessary. With your wrench,

loosely secure the cabinet hardware.

Do not tighten; this will allow you to

make adjustments once all of the cabi-

nets are installed.

Note: If you will be installing a high

cabinet, final adjustments and tight-

ening of the mounting hardware

should be done after the high cabi-

net is installed to ensure that every-

thing is level.

wall cabinets have been

drywall

line, tap