Bristan Java Eco Click J EBAS C Petunjuk Pemasangan & Daftar Isi - Halaman 2

Jelajahi secara online atau unduh pdf Petunjuk Pemasangan & Daftar Isi untuk Produk Pipa Bristan Java Eco Click J EBAS C. Bristan Java Eco Click J EBAS C 2 halaman. Basin mixer

Halaman Cetak
WATER PRESSURE
This mixer is suitable for use at all supply pressures. However for optimum use both
the hot and cold supplies should be reasonably balanced. If the fitting is installed at
low pressure (tank fed), then the minimum distance from the outlet of the nozzle to
the underside of the cold tank should be approximately 2.0 metres to ensure
adequate performance.
This mixer should be installed in compliance with Water Regulations. Where the
supplies are unbalanced, i.e. hot water from the cylinder tank/cold from the mains,
approved check val v es must be fitted in the supply pipes. For further details contact
your Local Water Authority.
c
d
e
a
b
f
1
2
3
15
4
5
6
8
7
10
9
Please Note:
In the unlikely event you find a part missing please contact our customer service
helpline on 0870 4425553 for i m mediate dispatch of part.
For latest prices and delivery to your door visit MyTub Ltd 0845 303 8383 www.mytub.co.uk
CONTENTS
1. Mixer body
(X1)
2. Pop-up operating rod ( X1)
3. Plinth
(X1)
4. C-shaped rubber was her (X1)
5. C-shaped metal washer (X1)
6. Nut
(x2)
7. Tailpipe
(x2)
8. Threaded rod
(x2)
9. Waste rod
(X1)
10. Waste body
(X1)
11. Washer
(X1)
12. Washer
(X1)
13. Waste flange
(X1)
14. Plug
(X1)
15. O-ring
(X1)
14
13
12
11
INSTALLATION
1. Identify all components and check for completeness, particularly before arranging
fitting.
2. Fit the mixer body (1) to the basin/bidet using the 'C' plate fixing kit. The plinth (3)
and 'O' ring (15) go between the fitting and the basin/bidet, and the 'C' shaped
rubber (4) and metal washers (5) on the underside of the basin/bidet. Secure into
position using threaded rods (8) and nuts (6).
3. Fit the inlet connection tailpipes (7) to the fitting and connect the hot and cold
supplies.
4. Fit the pop up waste, using washers (11) below & (12) above the basin/bidet and
connect it to the mixer. It is recommended that a silicon sealant be applied to both
sealing faces of washers (11) and (12) The waste can be set by adjusting the waste
rod (9) / operating rod (2) connecting bracket and the screw in the base of the plug
(14).
5. Fully open the mixer in the mid position, letting it run for a few minutes to check
all joints and connections for leaks.
6. See over the page for aftercare instructions.
ECO CLICK
An innovative water saving feature that offers a subtle
resistance as it reaches approximately half of its full flow
capability. For increased flow this feature can be overridden.
At full flow the eco click cartridge uses 32% less water than a
standard cartridge and when in eco click mode the reduction
increases to 72%.
MAINTENANCE
If the fitting begins to drip:
1. Turn off the water supply.
2. Remove indice cap (a), loosen grub screw (b) with a hexagon key and pull off
head (c), unscrew shroud (d) retaining nut (e).
3. Remove cartridge (f).
4. Clean or replace cartridge, clean and grease seal and refit. Note: There are
locating pins on the bottom of the cartridge that fit in holes inside the tap, to ensure
it is fitted the right way round.
5. Replace cartridge and head and turn on the water supply.
6. Contact our helpline if problem persists.