Bristan Prism Eco Click Petunjuk Pemasangan & Daftar Isi - Halaman 2

Jelajahi secara online atau unduh pdf Petunjuk Pemasangan & Daftar Isi untuk Produk Pipa Bristan Prism Eco Click. Bristan Prism Eco Click 2 halaman. Basin mixer

Halaman Cetak
WATER PRESSURE
This mixer is suitable for use at all supply pressures. However for optimum use
both the hot and cold supplies should be reasonably balanced. If the fitting is
installed at low pressure (tank fed), then the minimum distance from the outlet of
the nozzle to the underside of t h e cold tank should be 2.0 metres to ensure
adequate performance.
This mixer should be installed in compliance with Water Regulations. Where the
supplies are unbalanced, i.e. hot water from the cylinder tank / cold from the
mains, approved check valves must be fitted in the supply pipes. For further
details contact your Local Water Authority.
19
18
1
2
3
17
4
5
16
15
6
14
7
13
8
12
11
20
9
Please Note:
In the unlikely event you find a part missing please contact our customer service
helpline on 0870 4425553 for immediate dispatch of part.
For latest prices and delivery to your door visit MyTub Ltd 0845 303 8383 www.mytub.co.uk
CONTENTS
1. Head
(x1)
2. Shroud
(x1)
3. Retaining Nut
(x1)
4. Mixer Body
(x1)
5. Full Rubber Washer (x1)
6. Metal 'C' Washer
(x1)
7. Threaded Rods
(x 2)
8. Operating Rod
(x1)
9. Waste Rod
(x1)
10. Bottom Waste
(x1)
11. Washer
(x1)
12. Washer
(x1)
13. Top Waste
(x1)
14. Nuts
( x 2)
15. Plug
(x1)
16. Rubber 'C' washer (x1)
17. Cartridge
(x1)
10
18. Lever
(x1)
19. Grub Screw
(x1)
20. Tail pipes
(x2)
INSTALLATION
1. Identify all components and check for completeness, particularly before
arranging fitting.
2. Fit the mixer body (4) to the basin/bidet using the 'C' plate fixing kit (6 & 16).
The full rubber washer (5) goes between the fitting and the basin, the 'C' shaped
rubber (16) and metal washer (6) on the underside of the basin/bidet. Use the
threaded rods (7) and nuts (14) to secure to basin.
3. Fit the tail pipes (20) to the fitting and connect the hot and cold supplies.
4. Fit the pop up waste, and connect it to the mixer using washer (12) and the
top of the waste (13) above the basin, and washer (11) and bottom of waste (10)
on the underside. It is recommended that silicon sealant be applied to both
sealing faces of washers (11 and 12). The waste can be set by adjusting the
waste rod (9) / operating rod (8) connecting bracket and adjusting screw in the
base of the plug (15).
5. Fully open the mixer in the mid position, letting it run for a few minutes to
check all joints and connections for leaks.
6. See over the page for aftercare instructions.
ECO CLICK
An innovative water saving feature that offers a subtle
resistance as it reaches approximately half of its full flow
capability. For increased flow this feature can be overridden.
At full flow the eco click cartridge uses 32% less water than
a standard cartridge and w hen in eco click mode the
reduction increases to 72%.
If the fitting begins to drip:
1. Turn off the water supply.
2. Unscrew handle lever (18), loosen grub screw (19) with a hexagon key and
pull off head (1).
3. Remove cartridge (17).
4. Clean or replace cartridge, clean and grease seal and refit. Note: There are
locating pins on the bottom of the cartridge that fit in holes inside the tap, to
ensure it is fitted the right way round.
5. Replace cartridge and head and turn on the water supply.