Majestic fireplaces FireStage UVDR36C Panduan Pemasangan dan Pengoperasian Pemilik Rumah - Halaman 7
Jelajahi secara online atau unduh pdf Panduan Pemasangan dan Pengoperasian Pemilik Rumah untuk Perapian Dalam Ruangan Majestic fireplaces FireStage UVDR36C. Majestic fireplaces FireStage UVDR36C 16 halaman. The firestage series vent-free fireboxes
Juga untuk Majestic fireplaces FireStage UVDR36C: Brosur & Spesifikasi (6 halaman)
Halaman Cetak
Finishing Material
Noncombustible Material
Caulking or Sealant
Side View
Stand-
Noncombustible
off
Insulation
Top View
Fig. 7 Sealing spaces between fireplace and finishing materi-
als.
Finishing the Fireplace
There are a wide variety of finishing materials avail-
FP568
able for your fireplace from formal wall treatments with
UVBR/CN
7/01
marble and mantels to rustic wood paneling, stone or
brick.
IT IS IMPORTANT THAT THE BLACK FACE OF THE
FIREPLACE NOT BE COVERED WITH ANY TYPE OF
COMBUSTIBLE MATERIAL.
Noncombustible facing materials such as marble, brick
or ceramic tile may overlap the black face of the fire-
place up to the opening on either side of the fireplace.
Seal all joints between the black fireplace face and the
wall covering with a heat-resistant material such as rock
wool insulation or mortar. Be sure to use high tempera-
ture adhesive or mortar when anchoring brick, stone or
tile to the face of the fireplace. Check to see whether
man-made brick and stone are made of noncombustible
materials before using them on the face of the fireplace.
Some of these products contain combustible materials.
Combustible wall coverings such as paneling or wall-
board may not overlap the black face of the fireplace.
The space between the wall covering and the fireplace
should be sealed with a heat-resistant material such as
rock wool insulation or mortar.
NOTE: An "L" shaped steel lintel must be installed
across the top of the firebox opening where facing
materials such as brick or stone are used on the face
of the firebox. It acts as a support/firestop. It should be
attached to the face of the fireplace with screws and
sealed to the fireplace with a heat-resistant sealer.
WARNING: The firebox screens must be in place be-
fore operating the fireplace.
WARNING: These vent free fireplaces are not to be
used with glass doors.
20007469
Stud
Insulation
Finishing Material
Caulking or Sealant
A hearth extension may be used but is not required for
these fireboxes.
A raised hearth extension may be used as shown in
Figure 8.
Seal with Noncom-
bustible Material
Hearth
Extension
Surround
FP568
Combustible
Plateform
Fig. 8 A raised hearth extension.
Pre-Wiring of Junction Box
Wiring should be connected at the junction box located
on the right side of the firebox prior to the installation of
the blower kit. A standard wall box should be used to
contain the SCVS - Variable Speed Control Kit.
If an electrical supply of 120V is being roughed in to the
fireplace junction box to provide for future installation of
optional blower kit, the wiring should be connected to
the junction box located on the right side of the firebox.
NOTE: All electric connections are to be made in ac-
cordance with CSA Standard C22.1-Canadian Electrical
Code part 1 or with the National Electrical Code, ANSI/
NFPA 70 (latest edition) and/or in accordance with local
codes.
CAUTION: Should this blower require servicing, the
power supply must be disconnected.
120
Volt
G
Wall Electrical Box
Fig. 9 Blower wiring diagram.
UVDR Series Unvented Gas Fireplaces
Hearth Extension
Hearth Brick
1/2"
Combustibles Al-
lowed
(no carpet or vinyl)
T238
Hearth Extension
2/26/04 djt
Electrical Services
M
Speed Control
Switch
Black
White
T229
Blower
wiring diagram
2/11/04 djt
T238
Firebox Acces-
sory Junction
Box
T229
7