Airflow 72682307 Panduan Memulai Cepat

Jelajahi secara online atau unduh pdf Panduan Memulai Cepat untuk Kipas angin Airflow 72682307. Airflow 72682307 2 halaman. Modules for selv 12v fan range

Halaman Cetak

Modules for SELV 12V Fan Range

Installation and Operating Guide

Electrical installation

All electrical installation work to be carried out by an ap-

proved competent person in compliance with U.K. Building

Regulations and to the latest IET standards, or the appropri-

ate regulations in the country of installation. (for fan installa-

tion see the iCON SELV 12V Fan Range Installation and

Operating Guide).

Diagram A - module wiring with no external switching

(module functionality / pull cord activation only):

Diagram B - module wiring with external switching (live

trigger connection used):

PCS - 72573603

PCTS - 72574204

DTS - 72682307

HTS - 72574202

PRTS - 72574203

PRHTS - 72574201

Certificate No. EMS 569454

BS EN ISO 14001:2015

Page 3 of 8

iCON SELV Fan Range Available Modules

Airflow iCON SELV 12V fans can be controlled by optional

control modules. For the SELV 12V range you can choose

between six modules.

Part no.*

Model

72573603

PCS

72574204

PCTS

72682307

DTS

72574202

HTS

72574203

PRTS

72574201

PRHTS

* For blister pack add "B" at the end of part number.

SAFETY FIRST: ALWAYS ISOLATE THE FAN

UNIT FROM THE POWER SUPPLY BEFORE

DOING ANY WORK ON THE FAN/MODULE.

Certificate No. FM 00152

BS EN ISO 9001:2015

To install the module in an iCON fan follow the instructions

below. See page 5 - 8 for instructional drawings.

1. Remove the iCON fan front cover (see page 5).

2. Lift the fan electrical terminal away from its mounting pillars

and position on the module connector pins. Tighten the two

screws with a suitable screwdriver. Ensure the leads are

under the module retaining cable clamp.

3. Fit the module at a slight angle into the fan housing, ensur-

ing that the locating slot is fully engaged in to the locating

block on the fan.

4. Push the module against housing, ensuring the module clip

holds it in place (clicks at the cable clamp). With iCON 15

& 30 the terminal will reposition back over mounting pillars.

Modules with pull cord: Ensure that the pull cord is properly

located within the cord slot at the bottom of the fan.

Modules with PIR control: Remove the oval logo cap fitted

at the bottom of the front cover of the fan. Replace it with

translucent lens supplied with the PIR module. Note: The

lens must be replaced in order for the PIR module to function

properly. Ensure the orientation of the lens is correct (i.e. the

lens should be flush with the surface).

Connecting mains cable into the module

Connect the 12V Power Supply Unit cable to the 3-way sup-

ply connector block (see wiring diagrams on page 3) ensur-

ing that the supplied cable clamp is fitted. Refit the front

cover.

Note: When using DTS module on initial connection the fan

will start immediately and continue running for the duration

set on the timer function of the module.

Description

Pull cord

(Manual on/off)

Pull cord timer

(Pull cord, Run on timer 1 - 30 min)

Delayed timer

(Pull cord, 2 min delay, Run on timer 2 - 45 min)

Humidity timer

(Pull cord, Run on timer 1 - 30 min, 40 - 90% RH)

PIR timer

(Motion sensor, Run on timer 1– 30 min, 40 - 90% RH)

PIR humidity timer

(Motion sensor, Run on timer 1 - 30 min, RH

40 - 90%)

Page 2 of 8

Mechanical installation

Page 4 of 8

A, B