KitchenAid Architect Series II KFGS366VSS Panduan Petunjuk Instalasi - Halaman 5

Jelajahi secara online atau unduh pdf Panduan Petunjuk Instalasi untuk Kompor KitchenAid Architect Series II KFGS366VSS. KitchenAid Architect Series II KFGS366VSS 20 halaman. 30" (76.2 cm) and 36" (91.4 cm) gas built-in cooktop
Juga untuk KitchenAid Architect Series II KFGS366VSS: Dimensi (1 halaman), Panduan Dimensi (1 halaman)

Halaman Cetak

Gas Supply Line

Provide a gas supply line of

cooktop location. A smaller size pipe on longer runs may

result in insufficient gas supply. Pipe-joint compounds that

resist the action of LP gas must be used. Do not use

TEFLON

®†

tape. With LP gas, piping or tubing size should be

½" minimum. Usually, LP gas suppliers determine the size

and materials used in the system.

Flexible metal appliance connector:

If local codes permit, use a

steel tubing gas connector, designed by CSA to connect

the cooktop to the rigid gas supply line.

A ½" male pipe thread is needed for connection to the

female pipe threads of the inlet to the cooktop pressure

regulator.

Do not kink or damage the flexible metal tubing when

moving the cooktop.

Rigid pipe connection:

The rigid pipe connection requires a combination of pipe

fittings to obtain an in-line connection to the cooktop. The

rigid pipe must be level with the cooktop connection. All

strains must be removed from the supply and fuel lines so

cooktop will be level and in line.

Must include a shutoff valve:

The supply line must be equipped with a manual shutoff

valve. This valve should be located in the same room but

external to the cooktop. It should be in a location that allows

ease of opening and closing. Do not block access to shutoff

valve. The valve is for turning on or shutting off gas to the

cooktop.

A. Gas supply line

B. Shutoff valve "open" position

C. To cooktop

†®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

" (1.9 cm) rigid pipe to the

" or

" I.D. flexible stainless

Gas Pressure Regulator

The gas pressure regulator supplied with this cooktop must be

used. The inlet pressure to the regulator should be as follows for

proper operation:

Natural Gas:

Minimum pressure: 5" (12.7 cm) WCP

Maximum pressure: 7" to 14" (17.8 cm to 35.5 cm) WCP

LP Gas:

Minimum pressure: 11" (27.9 cm) WCP

Maximum pressure: 14" (35.5 cm) WCP

Contact local gas supplier if you are not sure about the inlet

pressure.

Burner Input Requirements

Input ratings shown on the model/serial rating plate are for

elevations up to 2,000 ft (609.6 m).

For elevations above 2,000 ft (609.6 m), ratings are reduced at a

rate of 4% for each 1,000 ft (304.8 m) above sea level (not

applicable for Canada).

For elevations above 6,560 ft (1999.5 m) a high altitude kit is

needed to avoid any reduced power output. See separate LP gas

conversion instructions sheet.

Gas Supply Pressure Testing

Gas supply pressure for testing regulator must be at least

1" water column pressure above the manifold pressure shown on

the model/serial rating plate.

Line pressure testing above ½ psi gauge (14" WCP)

The cooktop and its individual shutoff valve must be

disconnected from the gas supply piping system during any

pressure testing of that system at test pressures in excess of

½ psi (3.5 kPa).

Line pressure testing at ½ psi gauge (14" WCP) or lower

The cooktop must be isolated from the gas supply piping system

by closing its individual manual shutoff valve during any pressure

testing of the gas supply piping system at test pressures equal to

or less than ½ psi (3.5 kPa).