KitchenAid GSU-42-E-2 Panduan Petunjuk Instalasi - Halaman 7

Jelajahi secara online atau unduh pdf Panduan Petunjuk Instalasi untuk Kompor KitchenAid GSU-42-E-2. KitchenAid GSU-42-E-2 8 halaman. 42" gas cooktop with broiler/griddle

Halaman Cetak

L:yht

burner,

then

iurn

left handle

to raise gl-ill until

slots

in burner

heat shield

are seen. Turn

burner

"low"

and remove

iknob.

Hold

base of valve

stem with

pliers,

insert

narrow

(3/16")

standard

blade

screw-

dr 1ve: inlo

adjustment

screw

slot,

Looking

through

the

slots

in the

heat

shield,

adjust

until

flame

with

7, 16'

soft blue innFIr corle is reached.

li16"

SOFT

BLUE

INNER

CORE

BHOILER/'GRIDDL.E

ADJUSTMENT

The

Brolleritirlddle

has been properly

adjusted

at the factory.

Should

it be out of adjustment

at time

installation

as a resL)t of vibration

or handling

during

shipping,

correct

as shown

below.

Btoller

Handle

~- Correct

position

tor

handle

on left

(facing

cooktop)

is straight

up and down.

Before

making

any adjustments,

make

sure that

set screw

in handle

is tight.

Removal

of the top,

both

burners

ano the burner

support

on the left side is suggested

for the easiest

access to the adjustment

hardware.

The hand!e

is adjusted

loosening

the nuts

holding

the connecting

bar to the griddle

lift spring

casting.

iJ;ing

a 7/"16"

ooeln end wrench,

loosen

front

nut to lower

handle,

the rear nut to raise. Tighten

both

r:l-!tb to lock after

handle

is properly

positioned.

Griddle

Not

Prcperly

Counter

Balanced

Keep

In Set Position

Broiler

lift

spring

is designed

balance

the weight

of the griddle,

burner

and heat shield.

Once

again

the removal

of the top and left-

hand

parts

is suggested.

Hold

hook

bolt

firm

with

pliers

or screwdriver.

Use a 3/8"

open

wrench

tighten

or ioosery nut to obtain

desired

spring

tension

to hold griddle

in place as it is moved,

-;, -.

Broi!er

Pan ~- TLlis should

be level (both

front

to back and right

to left)

or parallel

with

the top surface

when

pan IS in i:s highest

position.

This

situation

is corrected

by loosening

the lock

nuts on the front

sling

adjustment

hook

which

is connected

to the sling

link

assembly.

The sling link assembly

connects

rhe front

and rear siing

links

to provide

for the raising

or lowering

of the broiler

pan. The broiler

pan

should

slope

towards

the front

when

broiling

to allow

the grease to run into

the cup of the pan. This

adiustrnent

may ;Je lnade through

the right

front

burner

opening.

!'I.

GriddIE

- Tne

f,ont

of the griddle

should

rest on the front

flange

of the griddle

opening

in the top and

on the

:op

of four

(4) screws

in the

heat

shield

when

in the

cooking

position.

The griddle

may

leveled

by raisinG or lowering

the four

screws.

7-o c(3rrect

a!ignrnent

of the griddle,

so that

the right

and left spacing

is equal

and parallel

to the edges

of the too openiiig,

loosen

screws on the broiler

burner

neck and shift

burner

to correct.

-7-