DECKORATORS ALX CLASSIC Petunjuk Instalasi - Halaman 3

Jelajahi secara online atau unduh pdf Petunjuk Instalasi untuk Perbaikan Rumah DECKORATORS ALX CLASSIC. DECKORATORS ALX CLASSIC 3 halaman. Complete kit
Juga untuk DECKORATORS ALX CLASSIC: Petunjuk Instalasi (4 halaman)

Halaman Cetak
Step 6 Attach each bracket to the post with two 1-3/4" screws.
For rail kits: Baluster connectors are attached to bottom and top rail, but should be
fully tightened by hand to railing before being installed. Do not over tighten.
Step 7 Lay bottom rail on stairs against the posts with the predrilled holes facing up. The
distance between the post and the first baluster should be less than 4" and equal on both
ends. Mark the rail where it meets the inside of the installed brackets. Do the same with the
top rail, but with the predrilled holes facing down. Trim the top and bottom rails to length with
a 90 degree cut.
Step 8 A rail support is needed every 2 feet (2 are included in the 6ft kit, 3 in the 8ft kit).
Attach rail support connectors to the bottom of the lower rail at 2 foot intervals using included
screws. Predrill using a 1/8" drill bit. Mark the location of the rail support on the step tread and
attach the other rail support connectors to the step tread.
Step 9 Install the bottom rail between the posts by setting rail in brackets. Secure bottom rail
to brackets using two 3/4" screws. Tip: Use a driver extension bit to avoid marring the rail or
post with the drill chuck. Snap top trim piece to the rail bracket.
Step 10 Attach balusters to the lower rail by sliding onto the connectors. Stair connectors
are set at 35˚.
Step 11 Position the top rail between the posts. Check for plumb end-to-end and vertically.
Mark the bracket location on post and remove rail. Mark the screw locations using the
bracket as a guide, and predrill using a 1/8" drill bit. Attach a bracket to the post with two
1-3/4" screws at one end. Repeat for the other end. Lower the top rail into position, placing
the balusters onto the stair connectors while working from one end of the railing to the other.
Tap with a rubber mallet if needed to eliminate any gaps. Attach the rail to each bracket by
predrilling with a 1/8" drill bit and using two 3/4" screws. Tip: Use a driver extension bit to
avoid marring the rail or post with the drill chuck.
Step 12 Set post caps on each post. Gently tap with rubber mallet to secure.
THE DIAGRAMS AND INSTRUCTIONS IN THIS BROCHURE ARE FOR ILLUSTRATION PURPOSES ONLY AND ARE NOT MEANT TO REPLACE A LICENSED PROFESSIONAL. ANY CONSTRUCTION OR USE
OF THE PRODUCT MUST BE IN ACCORDANCE WITH ALL LOCAL ZONING AND/OR BUILDING CODES. THE CONSUMER ASSUMES ALL RISKS AND LIABILITY ASSOCIATED WITH THE CONSTRUCTION
OR USE OF THIS PRODUCT. THE CONSUMER OR CONTRACTOR SHOULD TAKE ALL NECESSARY STEPS TO ENSURE THE SAFETY OF EVERYONE INVOLVED IN THE PROJECT, INCLUDING, BUT NOT
LIMITED TO, WEARING THE APPROPRIATE SAFETY EQUIPMENT. EXCEPT AS CONTAINED IN THE WRITTEN LIMITED WARRANTY, THE WARRANTOR DOES NOT PROVIDE ANY OTHER WARRANTY,
EITHER EXPRESS OR IMPLIED, AND SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING CONSEQUENTIAL DAMAGES.
©2019 Universal Forest Products. Deckorators is a registered trademark of Deckorators, Inc. in the U.S. All rights reserved.
Post Cap
•
Mark Rail
for Length
Post
•
Distance
Between
Posts
Post
Base
Trim
Mark Rail
•
for Length
68956 U.S. Highway 131, White Pigeon, MI 49099
www.deckorators.com
Post
Base
Trim
Top and
Bottom Rail
Post
Base
Trim
10942 12/19
Post Cap
•
Mark Rail
for Length
Post
•
Distance
Between
Posts
Mark Rail
•
for Length
Stair Rail Bracket
Equal Spacing on Both Ends
Top Rail
•
Post
Cap
•
•
Rail
Support
Baluster
•
Connector
Po
Ca
Top and
Bottom Rail
Post
Base
Trim
•
fig. 7
Post
•
•
•
< 6
"
Bottom Rail
fig. 8