IKEA KNAPPA Manual

Jelajahi secara online atau unduh pdf Manual untuk Pencahayaan Rumah IKEA KNAPPA. IKEA KNAPPA 29 halaman. Lamp
Juga untuk IKEA KNAPPA: Manual Petunjuk Perakitan (6 halaman), Panduan Pengguna (12 halaman)

Halaman Cetak

ENGLISH

KNÄPPA

Desi gn and Quality

IKEA of Sweden

LR03 • AAA

PUTTING THE CAMERA TOGETHER

Please refer to the assembly instructions. The

2 AAA/LR03 batteries need to be inserted as

shown before assembling the camera.

TURNING THE CAMERA ON

Hold down the power/shutter button with your

finger for about 5 seconds. This is on the front

of the camera under the IKEA logo.

Check that the LED on the back of the camera

next to the viewfinder. A green light indicates

the camera is on.

TAKING A PICTURE

When the LED is green push the power/shutter

button firmly (about 2 seconds) until the LED

starts to blink green.

The LED will blink green for about 8 seconds

while the picture data is being processed. The

camera will not take another picture while the

LED is blinking. Once the LED stops blinking it

is ready to take the next picture.

TURNING THE CAMERA OFF

Hold down the power/shutter button with your

finger for about 5 seconds until the green LED

goes out. The camera will also turn itself off

after about 30 seconds if it is not used.

CONNECTING YOUR CAMERA TO A

COMPUTER

Connect the camera to your a computer using

the built-in USB connector. The IKEA logo

should face up when plugging the camera into

a USB port. Once connected the camera will

appear:

- on a Mac desktop as a folder.

- as a new device in 'My Computer' on a

Windows PC.

The camera does not need to be switched on

to transfer pictures.

DELETING PICTURES FROM THE CAMERA

If the LED on the camera flashes red, the

camera's internal memory is full. Before you

can take more pictures, you need to make

room for new pictures by deleting older ones.

To delete pictures make sure the camera is

turned on. Then use a paperclip to press the

delete button on the front of the camera for

about 5 seconds. Note! This will delete all the

pictures on the camera. Please back-up all the

pictures on a computer before pressing the

delete button.

LOW BATTERY

The LED on the camera will shine red when

the camera's battery power is low. You need to

replace the batteries as soon as you can.

BATTERY REPLACEMENT

Remove the plastic nuts and bolts at the top

of the camera, a place them in a safe place.

Remove the old batteries and then replace

making sure that the + and – symbols match

on the new batteries and circuit board. Then

reassemble.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's

authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

—Consult the dealer or an experienced radio/ TV technician for help.

TIPS

• To make sure that your pictures are not

blurred hold the camera still for about 3

seconds while pushing the power/shutter

button to make sure your pictures are not

blurry.

• To help keep the camera steady, rest it on

something to help keep it stable.

• To improve picture quality avoid low light

levels.