Avantco 177CAGR424 Panduan Pengguna - Halaman 7

Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Peralatan Makanan Komersial Avantco 177CAGR424. Avantco 177CAGR424 15 halaman. Commercial countertop griddles, charbroilers & ranges

Halaman Cetak

User Manual

First-Time Use

Against shock damage or rocking from transportation, the sides and waste tray have a protective

PVC film. Remove any plastics, straps, or protective film from the product before operating the

equipment.

COUNTERTOP GAS GRIDDLE, THERMOSTATIC & MANUAL

To protect the equipment against possible moisture damage between fabrication and installation on

site, the flat-tops are coated with a layer of vegetable shortening and brown paper.

In addition, you should remove grease and brown paper, cleaning should be performed with the aid

of a sponge, mild soap and water in small amount.

After this procedure, turn the burners on and leave them on for about 15 minutes, this will cause all

flat-top grill residue to be burned and eliminated. Only then will the equipment be ready for use.

COUNTERTOP GAS RADIANT CHAR BROILER

To protect the equipment against possible moisture damage between manufacture and installation

on site, the grills and baffle rails are coated with a layer of vegetable oil.

In addition, you should perform a cleaning with the help of a sponge, neutral soap and water in small

amounts. After this procedure, turn the burners on and leave them on for about 15 minutes, this will

cause all gas charbroiler residue to be burned and eliminated.

Only then will the equipment be ready for use.

COUNTERTOP GAS RANGE

You should perform a cleaning with the help of a sponge, neutral soap and water in small amounts.

Only then will the equipment be ready for use.

Product Ignition

If you need to adjust the pilot valves (one pilot valve corresponds to two burners) do the following:

Turn the pilot adjusting screw counterclockwise, then light the pilot with the aid of the igniter

1 .

(wick) accompanying the product and adjust the flame to a height of approximately 0.5 cm;

2 .

Turn on the gas valve by turning the knob counterclockwise to light the main burners;

To shut down completely, close the gas valves by turning the knob clockwise and turn the pilot

3 .

adjusting screw clockwise to close the gas for the pilots.

COUNTERTOP GAS GRIDDLE, THERMOSTATIC

1. Open the manual gas supply valve (which will release gas

into the product);

2. Immerse in alcohol the lighter (wick) that accompanies

the product and light it; Note: Make sure that the container

where the alcohol is located is away from the product and

wick after immersing.

3. Press lightly and rotate the handle to the pilot position.

4. Keep it pressed and take the igniter (wick) passing

between the pilot flame ignition hole in the product panel

until it comes into contact with the pilot and ignites the

flame;

5. Keep the knob pressed for 10 seconds after the pilot

flame is lit and turn the knob counterclockwise until

the wished temperature (use the knob to adjust the

temperature);

6. Make sure the burner is lit. If the burner does not light,

repeat the procedure;

COUNTERTOP GAS GRIDDLE, MANUAL

1. Open the manual gas supply valve (which will release gas

into the product).

2. Immerse in alcohol the lighter (wick) that accompanies

the product and light it; Note: Make sure that the container

where the alcohol is located is away from the product and

wick after immersing;

3. Take the igniter (bypass) past the ignition hole in the

flame of the pilot on the product panel until contact with the

pilot burner and until the flame ignites, repeat this procedure

on all pilots (see following image); Note: The ignition order

does not interfere with the use of the equipment;

4. Turn the knob corresponding to the burner you wish to

operate counterclockwise (adjust the flame through the

knob);

5. Make sure the burner is lit. If the burner does not light,

repeat the procedure;

6. After lighting all burners, you can turn off the burners

and turn them back on simply by turning the corresponding

knobs; Note: The pilot burner flame is factory set

according to the gas for which the product was originally

manufactured. Always check through the hole identified on

the panel as PILOT, if the pilot burner flame is lit. If it is not,

perform the procedures described above again.

www.AvantcoEquipment.com

User Manual