IKEA LAGAN Panduan Penggunaan & Perawatan - Halaman 14

Jelajahi secara online atau unduh pdf Panduan Penggunaan & Perawatan untuk Mesin pencuci piring IKEA LAGAN. IKEA LAGAN 25 halaman. Examples of the load of the basket
Juga untuk IKEA LAGAN: Manual Petunjuk Perakitan (8 halaman), Panduan Pengguna (20 halaman), Panduan Pengguna (16 halaman), Panduan Pengguna (20 halaman), Petunjuk Manual (48 halaman), Panduan Pengguna (16 halaman), Panduan Pengguna (24 halaman), Manual (28 halaman), Buku Petunjuk (24 halaman), Panduan Pengguna (24 halaman), Manual (24 halaman), Manual (4 halaman), Panduan Pengguna (12 halaman), Manual (24 halaman), Manual Petunjuk Perakitan (20 halaman), Panduan Instalasi (20 halaman), Manual (28 halaman), Manual (32 halaman), Manual (44 halaman), Manual (16 halaman), Manual (16 halaman), Manual (24 halaman), Manual (28 halaman), Manual (28 halaman), Panduan Pengguna (28 halaman), Manual (40 halaman), Manual (48 halaman), Manual (44 halaman), Manual (40 halaman), Manual (28 halaman), Manual (28 halaman), Panduan Pengguna (24 halaman), Manual (48 halaman), Panduan Pengguna (16 halaman), Panduan Petunjuk Instalasi (18 halaman), Manual (48 halaman), Panduan Memulai Cepat (4 halaman), Panduan Petunjuk Instalasi (16 halaman), Manual (28 halaman), Manual (28 halaman), Manual (44 halaman), Manual (48 halaman), Manual (16 halaman), Manual (32 halaman), Manual (24 halaman), Manual (25 halaman), Manual (18 halaman), Panduan Pengguna (28 halaman), Manual (44 halaman), Manual (24 halaman), Manual (32 halaman), Manual (18 halaman), Manual (48 halaman), Manual (29 halaman), Manual (29 halaman), Manual (34 halaman), Panduan Petunjuk Instalasi (42 halaman)

Halaman Cetak
IKEA LAGAN Panduan Penggunaan & Perawatan
WATER SUPPLY CONNECTION
To Connect Water Supply Line To
The Ice Maker Inlet Valve
1. Disconnect the refrigerator from the
electrical power source.
2. Place the end of the water supply
line into a sink or bucket. Turn ON
the water supply and flush the sup-
ply line until the water is clear. Turn
OFF water supply at shutoff valve.
3. Remove plastic cap from water valve
inlet and discard cap.
4. If you use copper tubing - Slide
brass compression nut, then ferrule
(sleeve) onto water supply line. Push
water supply line into water valve
inlet as far as it will go (¼ in. / 6.4
mm). Slide ferrule (sleeve) into valve
inlet and finger tighten compression
nut onto valve. Tighten another
half turn with a wrench; DO NOT
overtighten. See Figure 1.
If you use braided flexible
stainless steel tubing - The nut
is already assembled on the tubing.
Slide nut onto valve inlet and finger
tighten nut onto valve. Tighten
another half turn with a wrench; DO
NOT overtighten. See Figure 2.
5. With steel clamp and screw, secure
water supply line (copper tubing only)
to rear panel of refrigerator as shown.
6. Coil excess water supply line (copper
tubing only), about 2½ turns, behind
refrigerator as shown and arrange
coils so they do not vibrate or wear
against any other surface.
7. To turn ice maker on, press the ice
maker's On/Off power switch so the
LED is steadily illuminated.
8. Turn ON water supply at shutoff
valve and tighten any connections
that leak.
14
9. Reconnect refrigerator to electrical
power source.
Plastic Water Tubing
to Ice Maker
Fill Tube
Copper water line from
household water supply
(Include enough tubing in loop to allow
moving refrigerator out for cleaning.)
Figure 1
Plastic Water Tubing
to Ice Maker
Fill Tube
braided flexible stainless steel
water line from household water supply
(Include enough tubing to allow
moving refrigerator out for cleaning.)
Figure 2
EN
Steel Clamp
and Screw
Brass
Compression
Nut
Ferrule
(Sleeve)
Copper
Water Valve
Bracket
Valve Inlet
Water Valve
Braided
Flexible
Stainless
Steel
Water Line
Water Valve
Bracket
Valve Inlet
Water Valve
6 ft minimum (1.8 m)