ALIBI ALI-BC700G Panduan Instalasi Cepat - Halaman 2
Jelajahi secara online atau unduh pdf Panduan Instalasi Cepat untuk Kamera Keamanan ALIBI ALI-BC700G. ALIBI ALI-BC700G 3 halaman. Ali-bc700 series infrared bullet cameras
Halaman Cetak
ALI-BC700VFG camera typical wall mounting
If mounting the camera on a wall, ensure that the label on the mounting base, "
NOTE
If mounting the camera on a ceiling, orient the mounting base so that the cable guide is pointing
away from any source of water, dust, and other contaminates.
1.
Using the drill template provided, mark the location of the screws that anchor the mounting base
to the mounting surface. See the note above. If you are routing the drop cable through mounting
surface, also mark the position of the hole for the drop cable.
2.
Drill holes for the screws that anchor the base to the mounting surface. The mounting hardware
provided is appropriate for most surfaces. However, depending on the surface materials, more
appropriate fasteners may be required.
3.
Drill a 3/4" hole through the mounting surface for the drop cable, if necessary.
4.
Route the drop cable through the hole in the mounting surface, or through the cable guide in the
mounting base, then attach the camera assembly to the surface using the appropriate fasteners.
5.
Connect the camera drop cable to video and power extension cables as required.
6.
Connect the other end of the video extension cable to a video monitoring device, such as a CCTV
system monitor or DVR.
Drop cable connectors are not waterproof.
NOTE
7.
Connect the other end of the power extension cable to a 12 Vdc power source. Observe the polarity
of the cable shown in the photo on page 1 of this guide.
Camera adjustments
1.
Apply power to the camera.
2.
Verify that video from the camera can be seen on the monitor.
3.
While observing video from the camera, loosen the mounting bracket pan, elevation and horizontal
line adjustment lock screws, point the camera at your surveillance target, and then tighten
adjustment lock screws or nuts to hold the camera in position.
For the ALI-BC700G camera: The mounting bracket pan adjustment can be made after loosening
the lock nut (see the photo below). Use a Phillips #1 screwdriver for the elevation and horizontal line
adjustment lock screws.
Use for pan
adjustment
(lock nut)
Use for
elevation
adjustment
0° ~ 90°
0° ~ 360°
ALI-BC700G camera mounting bracket adjustment
For the ALI-BC700VFG camera: Use Phillips #2 screwdriver for the pan, elevation and horizontal
line adjustment lock screws.
www.observint.com
2
Bottom
Use for horizon line
adjustment
0° ~ 360°
Use for pan
Adjustment
Use for
Elevation
Adjustment
0° ~ 90°
0° ~ 360°
," is down.
4.
Adjust the sun shield (forward or back) to shield the lens from direct light, if necessary.
5.
If your camera has a varifocal lens (ALI-BC700VFG only), remove the cover on the underside of the
camera (slide the cover forward to remove) to access the focus and zoom adjustment screws. Use
the tool on the cover to adjust the zoom and focus if needed, and then reinstall the cover.
Adjustment tool
Cover
Specifications
Model
Image Sensor:
Signal System:
Effective Pixels:
Min. Illumination:
Shutter Time:
Lens:
Lens Mount:
Adjustment Range:
Day& Night:
Horizontal Resolution:
Synchronization:
Video Output:
S/N Ratio:
BLC:
Operating Conditions:
Humidity:
Power Supply:
Power Consumption:
Weather Proof:
IR Range:
Dimension:
Weight:
Use for Horizon Line
Adjustment
0° ~ 360°
ALI-BC700VFG camera mounting bracket adjustment
adjustment
adjustment
ALI-BC700VFG camera Focus - Zoom adjustment
ALI-BC700G
1/3" DIS
NTSC
976(H) × 496(V)
0.1 lux @ (F1.2, AGC on),
0 lux with IR
1/30 sec to 1/15,000 sec
3.6 mm
Angle of view: 68.4° (3.6 mm)
M12
Pan: 0 - 360°, Tilt: 0 -90°, Rotation: 0 - 360°
IR cut filter with auto switch
700 TVL
Internal synchronization
1 Vp-p composite output (75 Ω/BNC)
More than 62 dB
On
-40 °F ~ 140 °F (-40 °C ~ 60 °C)
90% or less (non-condensing)
12 Vdc ± 10%
Max. 1.8 W, (Max. 4 W with IR cut filter on)
IP66
32 ~ 65 ft (10 ~ 20 m) approx.
Φ2.76" × 5.89" (Φ70 × 149.5 mm)
0.79 lbs (360 g)
© 2014 Observint Technologies. All rights reserved.
Focus
Zoom
ALI-BC700VFG
1/3" DIS
NTSC
976(H) × 496(V)
0.1 lux @ (F1.2, AGC ON),
0.14 lux @ (F1.4, AGC ON),
0 lux with IR
1/60 sec to 1/100,000 sec
2.8 ~ 12 mm @ F1.4
Angle of view: 80° - 27.2°
φ14
Pan: 0 - 360°, Tilt: 0 - 90°, Rotation: 0 - 360°
IR cut filter with auto switch
700 TVL
Internal synchronization
1 Vp-p composite output (75 Ω/BNC)
More than 62 dB
On
-40 °F ~ 140 °F (-40 °C ~ 60 °C)
90% or less (non-condensing)
12 Vdc ± 10%
Max. 4 W(Max. 5 W with IR cut filter on)
IP66
98 ~ 131 ft (30 ~ 40 m) approx.
Φ4.13" x 3.42" x 10.52"
(105 × 86.9 × 267.2 mm)
2.97 lbs (1350 g)