Makita AN942 Buku Petunjuk - Halaman 4
Jelajahi secara online atau unduh pdf Buku Petunjuk untuk Alat Listrik Makita AN942. Makita AN942 17 halaman. Pneumatic construction nailer
Juga untuk Makita AN942: Buku Petunjuk (20 halaman), Perincian Bagian (3 halaman), Informasi Teknis (7 halaman)
Halaman Cetak
Always check the tool for its overall condition
•
and loose screws before operation. Tighten as
required.
Make sure all safety systems are in working
•
order before operation. The tool must not oper-
ate if only the trigger is pulled or if only the con-
tact arm is pressed against the wood. It must
work only when both actions are performed.
Test for possible faulty operation with nails
unloaded and the pusher in fully pulled position.
Make sure that the trigger is locked when the
•
change lever is set to the LOCK position.
Check walls, ceilings, floors, roofing and the like
•
carefully to avoid possible electrical shock, gas
leakage, explosions, etc. caused by striking live
wires, conduits or gas pipes.
Use only nails specified in this manual. The use
•
of any other nails may cause malfunction of the
tool.
Never use fastener driving tools marked with the
•
symbol "Do not use on scaffoldings, ladders"
for specific application for example:
when changing one driving
-
location to another involves
the
use
stairs, ladders, or ladder alike
constructions, e.g. roof laths;
closing boxes or crates;
-
fitting transportation safety systems e.g. on
-
vehicles and wagons.
Do not permit those uninstructed to use the
•
tool.
Make sure no one is nearby before nailing.
•
Never attempt to nail from both the inside and
outside at the same time. Nails may rip through
and/or fly off, presenting a grave danger.
Watch your footing and maintain your balance
•
with the tool. Make sure there is no one below
when working in high locations, and secure the
air hose to prevent danger if there is sudden
jerking or catching.
On rooftops and other high locations, nail as
•
you move forward. It is easy to lose your footing
if you nail while inching backward. When nailing
against perpendicular surface, nail from the top
to the bottom. You can perform nailing opera-
tions with less fatigue by doing so.
A nail will be bent or the tool can become
•
jammed if you mistakenly nail on top of another
nail or strike a knot in the wood. The nail may be
SAVE THESE INSTRUCTIONS
4
of
scaffoldings,
thrown and hit someone, or the tool itself can
react dangerously. Place the nails with care.
Do not leave the loaded tool or the air compres-
•
sor under pressure for a long time out in the
sun. Be sure that dust, sand, chips and foreign
matter will not enter the tool in the place where
you leave it setting.
Do not point the ejection port at anyone in the
•
vicinity. Keep hands and feet away from the
ejection port area.
When the air hose is connected, do not carry the
•
tool with your finger on the trigger or hand it to
someone in this condition. Accidental firing can
be extremely dangerous.
Handle the tool carefully, as there is high pres-
•
sure inside the tool that can be dangerous if a
crack is caused by rough handling (dropping or
striking). Do not attempt to carve or engrave on
the tool.
Stop nailing operations immediately if you
•
notice something wrong or out of the ordinary
with the tool.
Always disconnect the air hose and remove all
•
of the nails:
When unattended.
1.
Before performing any maintenance or
2.
repair.
Before cleaning a jam.
3.
Before moving the tool to a new location.
4.
Perform cleaning and maintenance right after
•
finishing the job. Keep the tool in tip-top condi-
tion. Lubricate moving parts to prevent rusting
and minimize friction-related wear. Wipe off all
dust from the parts.
When not operating the tool, always lock the
•
trigger by turning the change lever to the LOCK
position.
Do not operate this tool if it does not contain a
•
legible WARNING LABEL.
Do not modify tool without authorization from
•
Makita.
Ask Makita's Authorized service centers for peri-
•
odical inspection of the tool.
To maintain product SAFETY and RELIABILITY,
•
maintenance and repairs should be performed
by Makita Authorized Service Centers, always
using Makita replacement parts.