Makita BFL400F Informasi Teknis - Halaman 4
Jelajahi secara online atau unduh pdf Informasi Teknis untuk Alat Listrik Makita BFL400F. Makita BFL400F 13 halaman. Cordless angle screwdriver
Juga untuk Makita BFL400F: Buku Petunjuk (17 halaman), Buku Petunjuk (13 halaman), Buku Petunjuk (10 halaman)
Halaman Cetak
[3] -1. Disassembling/ Assembling of Job Light Section (cont.)
Fig. 8
Ring spring 29
[3] -2. Disassembling/ Assembling of Bearing Retainer
DISASSEMBLING
Turn Bearing retainer clockwise using a 27mm spanner for BFL300F/ 32mm
spanner for BFL400F and BFL401F. Now Bearing retainer can be removed
by pushing it down as illustrated in Fig. 10.
ASSEMBLING
1) After applying Makita seal lubricant No.101 to O ring 15, put O ring 15 and
Bearing retainer in place on Spindle complete.
2) Put 2g of Makita seal lubricant No.101 in the gear room of Angle head complete.
At this time, be careful not to put the grease on the threaded portion of Angle head complete.
3) Apply Loctite 603 to the threaded portion of Bearing retainer, and screw it into Angle head complete.
At this time, remember to put Flat washer 5 in place.
4) Fasten Bearing retainer to the recommended torque of 30 - 50N.m by turning counterclockwise with the following tools;
1R219, 1R220, 1R222, 134844-7 (for BFL300F), 134848-9 (for BFL400F/ BFL401F)
[3] -3. Disassembling/ Assembling/ Adjustment of Angle Head Section
DISASSEMBLING
*Shown in Fig. 11 are the parts of Angle head section.
Fig. 11
10
10) Angle head complete
11) Spiral bevel gear 9
12) Needle bearing 1212
13) Thin washer 12
14) Spacer
1) Remove Light covers (R) and (L), Ring spring 29, Lead cover and Switch cover. (Refer to [3] -1.)
2) Fix Angle head by clamping its two flats using adjustable wrench or vise, and remove Hex nut M36-41 by turning
in the direction of the arrow with 1R223 and 1R341. (Figs. 12, 13)
Caution: When clamping Bearing retainer, be very careful not to deform it by overtightening.
3) Remove Angle head complete by turning counterclockwise.
4) Remove Retaining ring R-32 using 1R006 or the like, then Flat washer 26, Internal gear 50 and Carrier section.
5) Remove Retaining ring S-14 from Carrier section using 1R291 or the like. Now the following parts can be replaced;
Flat washer 14, Pin 3 (5pcs), Spur gear 14 (5pcs)
Note: Pin 3 can be pulled out easily by using a magnet.
6) Remove Retaining ring R-22 located inside Angle head complete using 1R005 or the like.
7) Remove Spiral bevel gear 9 section by hitting the end face of Angle head complete. (Fig. 14)
8) Remove Retaining ring S-10 from Spiral bevel gear 9 section using 1R004, 1R008 or the like.
Now the following parts can be replaced by removing Ball bearing 6900LLB with 1R269 or the like:
Spiral bevel gear 9, Spacer, Thin washer 12, Needle bearing 1212
Fig. 9
Spiral bevel gear 9 section
11
12
13 14
15 16
15) Ball bearing 6900LLB
16) Retaining ring S-10
17) Retaining ring R-22
18) Internal gear 50
19) Retaining ring S-14
Lead cover
Ring spring 36
Lead wire
Fig. 10
Carrier section
21 22
17
18
19 20
20) Flat washer 14
25) Retaining ring R-32
21) Pin 3 (5pcs)
22) Spur gear 14 (5pcs)
23) Carrier
24) Flat washer 26
P 4 / 13
Bearing retainer
23
24
25