Makita DCO140 Buku Petunjuk - Halaman 4
Jelajahi secara online atau unduh pdf Buku Petunjuk untuk Alat Listrik Makita DCO140. Makita DCO140 13 halaman. Cordless cut-out tool
Juga untuk Makita DCO140: Buku Petunjuk (13 halaman), Informasi Teknis (8 halaman)
Halaman Cetak
preventive safety measures reduce the risk of
starting the power tool accidentally.
20. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
21. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool's operation. If damaged, have the
power
tool
accidents are caused by poorly maintained power
tools.
22. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
23. Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
Battery tool use and care
24. Recharge only with the charger specified by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of fire
when used with another battery pack.
25. Use
power
tools
designated battery packs. Use of any other
battery packs may create a risk of injury and fire.
26. When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another. Shorting the battery
terminals together may cause burns or a fire.
27. Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water.
If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery
may cause irritation or burns.
Service
28. Have your power tool serviced by a qualified
repair
person
replacement parts. This will ensure that the
safety of the power tool is maintained.
29. Follow
instruction
changing accessories.
30. Keep handles dry, clean and free from oil and
grease.
repaired
before
use.
only with
specifically
using
only
for
lubricating
CORDLESS CUTOUT TOOL
SAFETY WARNINGS
1.
Hold
surfaces, when performing an operation
where the cutting accessory may contact
hidden wiring. Cutting accessory contacting a
"live" wire may make exposed metal parts of the
power tool "live" and could give the operator an
electric shock.
Many
2.
Use clamps or another practical way to secure
and support the workpiece to a stable
platform.Holding the work by your hand or
against the body leaves it unstable and may lead
to loss of control.
3.
Wear eye protection and dust mask.
4.
Ventilate your work area adequately.
5.
Check the bit carefully for cracks or damage
before
damaged bit immediately.
6.
Check for the proper clearance beneath the
workpiece before cutting so that the bit will
not strike a hard surface such as the floor,
workbench, etc.
7.
Do not cut metal objects such as nails and
screws. Inspect for and remove all nails,
screws and other foreign material from the
workpiece before operation.
8.
Check that the bit is not contacting the
workpiece before the switch is turned on.
Always hold the tool with two hands while
switching the tool on. The motor torque can
cause the tool to turn.
9.
Before using the tool on an actual workpiece,
let it run for a while. Watch for vibration or
wobbling
installed bit.
10. Make sure that the shaft lock is released
before the switch is turned on.
11.
Always use with the shoe securely attached to
the tool and positioned flat and firmly against
the workpiece.
12. Hold the tool firmly.
13. Do not perform any operation using your
identical
hands to support or guide the workpiece.
14. Keep hands away from moving parts.
15. Do not use this tool for drilling.
and
16. Do not leave the tool running. Operate the tool
only when hand-held.
17. Always switch off and wait for the bit to come
to a complete stop before removing the bit
from workpiece.
4
power
tool
by
insulated
operation.
Replace
that could
indicate improperly
GEB123-1
gripping
cracked
or