KitchenAid YKESC307HS7 Panduan Petunjuk Instalasi - Halaman 4
Jelajahi secara online atau unduh pdf Panduan Petunjuk Instalasi untuk Rentang KitchenAid YKESC307HS7. KitchenAid YKESC307HS7 9 halaman. 30" electric ranges with self-cleaning thermal/convection oven
Halaman Cetak
Excessive
Weight Hazard
Use two or more people to move and
install range.
Failure to follow this instruction can
result in back or other injury.
BAKED
OTHER
Firmly grasp the range and gently
lay it on its back on the cardboard
corners.
Control panels may vary.
'_]
ull cardboard bottom and shipping
base firmly to remove.
%
Use an adjustable wrench
to loosen the leveling legs
1-1/2 turns.
'_ Place cardboard or hardboard in
front of range. Stand range back up
onto cardboard or hardboard.
Tip Over Hazard
A child or adult can tip the range and
be killed.
Connect
anti-tip bracket
to rear range
foot.
Reconnect
the anti-tip
bracket, if the
range is moved.
Failure to follow these instructions can
result in death or serious burns to
children
and adults.
Place the anti-tip
bracket template
on the floor in
the cabinet
opening so that
the left edge is
against cabinets
and the top
edge is against
the rear wall,
molding or
cabinet. If
25" (63.5 cm) countertop
over
24" (61 cm) cabinet
_f---
j
<
anti-tip
bracket
countertop opening is deeper
template
than 25 inches (63.5 cm),
measure and mark a distance 25 inches
(63.5 cm) in from front of countertop
opening
and align template with mark
(or subtract 25 inches (63.5 cm) from
countertop depth and add the difference to
the 2-1!4-inch (5.7 cm) dimension).
A
25" (63.5
Counteffop
overnangs
cabinet
side.
A = Difference
between
counterfop
depth
and 25"
(63.5 cm).
A
bracket
template
slide-in
cutout
shown
If countertop is not flush to the side of
cabinet opening, align the left side of the
template to allow for the countertop
overhang. Tape the range anti-tip bracket
template in place.
Contact
a qualified
floor covering
installer for the best procedure
of drilling
mounting
holes through your type of
floor covering.
Before moving,
slide range onto
cardboard
or hardboard,
To mount anti-tip
bracket to wood
floor, use the anti-
tip bracket
template to mark
where to drill
mounting holes.
Use a drill with a
1/8" (0.3 cm) drill
bit to drill the two
holes. Remove template from floor.
To mount anti-tip
bracket to concrete
or
ceramic
floor, use the anti-tip bracket
template to mark where to drill mounting
holes. Use a drill with a 3/16" (0.48 cm)
masonry drill bit to drill the two holes.
Remove template from floor. Tap plastic
anchors into mounting holes in floor with
hammer.
Line up holes in anti-tip
"_\
bracket with holes in
floor. Use the screws
provided to fasten
anti-tip bracket
to floor.
NOTE: Anti-tip
bracket must be
mounted
securely
to the sub
floor. Depending on the thickness of your
flooring, longer screws may be necessary to
anchor the bracket to the sub floor. Longer
screws are available from your local
hardware store.
I1
Move range close to cabinet
opening. Make electrical
[] connection. See"Electrical
requirements" and "Electrical
connection," Panel B, for details. "8888"
should appear in the clock display. Refer to
Use and Care Guide for information on
electronic controls.
1
] Remove cardboard or hardboard
from under range. Carefully move
[] range into final position.
i12.
Press on front of storage drawer and release
to open. Pull open to first stop position. Lift
front of drawer to clear white wheels in
drawer guides. Remove drawer and set it
aside on a protected surface.
Look under range
(a flashlight may
be needed) to check
that left rear leveling
leg is engaged in the
anti-tip bracket. If
leveling leg is not properly engaged, remove
and reposition the anti-tip bracket to insure
that the leveling leg fits properly in the anti-
tip bracket.
[14.1
........
Place rack in
oven. Place level on rack,
first side to side; then front to back. If the
range is not level, pull range forward until the
rear leveling leg is removed from the anti-tip
bracket. Adjust the leveling legs up or down.
Then slide range back into position. Check
that leveling leg is engaged in anti-tip
bracket.
NOTE: Oven must be level for satisfactory
baking conditions.
Insert storage drawer into slide
11
_
am rails on sides of drawer opening.
Lift front of drawer slightly and
push firmly to close drawer.
Pushinand
turn each
,o
surface unit
control knob to "HI"
position. Check the
operation of the cooktop
¢%
elements and indicator
%
lights.
OFF
MED
1
7
] Check the operation of the oven
element. Press the "BAKE" pad.
[] "350°F '' will appear in the
temperature display. Press the "START" pad.
"Lo" will appear in the display; then "170°F ''
(when oven reaches 170°F).
The bottom element should glow red and
the indicator light should be on. The upper
element should become hot but not glow
red. As the oven temperature rises, the
temperature
in the display will increase in
5°F increments until the oven reaches the
set temperature.
Press "CANCEL/OFF"
pad.
1
i Check the operation of the broil
I
element. Close the oven door.
[] Press the "BROIL' pad. "500°F '' will
appear in the temperature display. Press the
"START" pad.
Look through the oven window. The top
element should glow red. Press the
"CANCEL/OFF"
pad.
To get the most
efficient
use from
your
new electric
range,
read your
KitchenAid
Use and Care Guide.
Keep Installation
Instructions
and
Guide
close
to the electric
range
for
easy reference.
Panel C