Empire VSM-24-1 Petunjuk Pemasangan dan Panduan Pemilik - Halaman 13

Jelajahi secara online atau unduh pdf Petunjuk Pemasangan dan Panduan Pemilik untuk Perapian Dalam Ruangan Empire VSM-24-1. Empire VSM-24-1 20 halaman. Vented slope glaze burner

Halaman Cetak

Thermostats are not approved on vented decorated

appliances.

Label all wires prior to disconnection when servicing controls. Wiring

errors can cause improper and dangerous operation. Verify proper

operation after servicing.

VSR gas valve does not require 24 or 110 volts. See Figure 10 to

provide optional wall switch or remote control.

It is important to use wire of a gauge proper for the length of the

wire:

ReCOMMeNded WIRe GAuGes

Maximum Length

1' to 10'

10' to 25'

25' to 35'

Use the two leads (black wires) from ON/OFF switch to attach

optional components.

Check system Operation

Millivolt system and all individual components may be checked with

a millivolt meter 0-1000 MV range.

750 Millivolt system

When you ignite the pilot, the thermocouple produces millivolts

(electrical current) which energizes the magnet in the gas valve.

After 30 seconds to 1 minute time period you can release the gas

control knob and the pilot will stay ON. Allow your pilot flame to

operate an additional one (1) to two (2) minutes before you turn the

gas control knob from the PILOT position to the ON position. This

time period allows the millivolts (electrical current) to buildup to a

sufficient level allowing the gas control to operate properly.

Millivolt Control

The valve regulator controls the burner pressure which should be

checked at the pressure test point. Turn captured screw counter

clockwise 2 or 3 turns and then place tubing to pressure gauge over

test point (Use test point "A" closest to control knob). After taking

pressure reading, be sure and turn captured screw clockwise firmly

to re-seal. Do not over torque. Check for gas leaks.

Remote Receiver -VsR-(18, 24, 30)

Use the following steps to place the remote receiver adjacent to

the gas valve.

Attention:

1. The remote receiver can not be placed behind the gas valve

and burner assembly.

Keep the control compartment, logs and burner area surrounding

the logs clean.

THE loGs cAN GET VERy HoT— HANdlE oNly WHEN

COOl.

Always keep the appliance area clear and free from combustible

materials, gasoline, and other flammable vapors and liquids.

Never obstruct the flow of combustion and ventilation air. Keep the

front of the appliance clear of all obstacles and materials.

26284-3-0813

WIRING

Wire Gauge

clEANING ANd sERVIcING

2. When facing the appliance, the remote receiver must be placed

in the right side firebox, toward the front.

NOTICE: Do not let remote control receiver come in contact with

burner assembly.

Refer to remote control installation and operating instructions for

more details on remote control.

VsR Wiring diagram (Figure 10)

VsR

NOTICE: (Wiring harness located in envelope)

Connect the 2 - 1/4" terminals onto the TH and TH/TP terminals

on valve. Place decorative log to right of the gas valve and burner

assembly. When connecting to remote receiver, cut off 1/4" terminals

from wires attached to ON/OFF switch. Strip wires back about 1/4".

Connect stripped ends into remote receiver.

Inspecting Venting system

A vented fireplace venting system is designed and constructed

to develop a positive flow adequate to remove flue gases to the

outside atmosphere.

Any foreign objects in the venting system, may cause spillage of

the flue gases into the room.

Periodic examination and/or cleaning of the venting system of the

solid-fuel burning fireplace must be done by a qualified service

person. Visually inspect the damper and flue area for excessive

soot build-up. This soot (carbon) may be removed by brushing with

a soft bristle brush.

Figure 10

Page 13