KitchenAid KEBC147KWH05 Petunjuk Instalasi - Halaman 4

Jelajahi secara online atau unduh pdf Petunjuk Instalasi untuk Oven KitchenAid KEBC147KWH05. KitchenAid KEBC147KWH05 5 halaman. 24" electric built-in single and double ovens

Halaman Cetak

Electrical connection

If your house has aluminum wiring, see

"Ebctrical requirernents", Page 2.

Electrbal Shock Hazard

Turn power supply off before connecting wires.

Use 8 gauge solid copper wire.

Electrically ground range.

Failure to follow these instructions can result

in death, fire, or electrical shock.

This oven is manufactured

with white

{neutraJ)

power supply wire and a cabinet=connected

bare

grounding

wire twisted

together.

Feed oven cane through opening in

the cabinet. Make electrical connection

following the steps needed for your installation.

1. Disconnect the power supply.

2. Remove the junction box cover.

3. Connect oven cable to junction box through the

U.L.-listed conduit connector.

4. Connect the two black wires together with

twist-on connectors.

5. Connect the two red wires together with

twist-on connectors.

6. Complete electrical connection according to

local codes and ordinances.

cable from

junction

power

supply

box _

re.,_

white _

-:_

w,re _

_>_

grounding

oven

cable wires

factory

crimped

Figure 1

cable from

oven

conduit

connector

ff local codes PERMIT

connecting

cabinet-grounding

conductor

to neutral white

wire in junction

box:

7. Connect the factory-crimped

bare and white oven cable wires

to the neutral (white) wire in

junction box. See Figure 1.

8. Replace junction box cover.

cabb from

iunction

power supply

Figure 2

cabte from

connector

oven

If local codes DO NOT PERMIT

connecting

cabinet-grounding

conductor

to neutral white

wire in junction

box:

7. Separate the factory-crimped

bare and white oven cable wires.

8. Connect white oven cable wire to

neutral (white) wire in junction

box. See Figure 2.

9. Connect the bare grounding

oven cable wire to a grounded

wire in the junction box. See

Figure 2.

10. Replace junction box cover.

If connecting

to a

four-wire electrical system:

7. Separate bare and white oven

cable wires.

8. Connect white oven cable wire

to neutral (white) wire in

junction box. See Figure 2.

9. Connect the bare grounding

oven cable wire to the green

grounding wire in junction box.

Do Not connect bare grounding

wire to neutral {white} wire in

junction box. See Figure 2.

10. Replace junction box cover.

Attachment

Carefully push against sea_area of oven front

frame when pushing oven into cabinet.

Do Not push against outside edges.

5[]

Lift oven into cabinet cutout using the

oven opening as an area to grip.

shipping

foot

Push against seal area of front frame to push

oven into cabinet until shipping feet almost

contact cabinet. Use a Phillips screwdriver to

remove screws attaching shipping feet. Remove

and discard shipping feet.

Push oven completely into cabinet and center

oven in cabinet cutout.

4 screws

6[]

Important: Securely fasten oven to cabinet

using the screws provided (two screws for a single

oven or four screws for a double oven). Insert the

screws through holes in mounting rails. Do Not

overtighten screws.

Slide top

of trim up.

Push trim

into place.

Repmace

trim screw.

7[]

Slide top end of each trim upward onto oven

side rails. Push each trim into place at bottom of

trim. Use screws to attach each trim to oven. Take

care not to scratch other surfaces with ends of trim.

8[]

Replace oven racks.

Important: Replace the door with the model/serial

rating plate on the upper oven.

On some models, the construction of this door is

designed to withstand self-cleaning temperatures.

9[]

Reinstall the oven door by inserting ends

of hinges into hinge slots in the oven frame. Push

hinges in as far as they will go, Open the door

(you will feel the door drop into place) and rotate

both binge tatches back to the locked position.

Close and open the door to check that the door

closes and opens completely,

if door does not

dose or open completely,

repeat the door

removal

step and reinstall

door as described

above,

Repeat for lower oven door.

Check operation

[] Turn on power supply. The display

panel will light up briefly. "PF" should appear in

the temperature display.

the display. Press the "START" pad. Make sure the

oven door is closed and the "ON" light is shown in

the display area. After 2 minutes, partially open

oven door. You should feel heat from the oven.

Press the "CANCEL" pad.

Check the operation of your double oven.

Press the "Upper Oven" pad. Press the "BROIL"

pad. "BROIL" will appear in the display. Press the

"START" pad. Make sure the oven door is closed

and the "ON" light is shown in the display area.

After 2 minutes, partially open oven door. You

should feel heat from the oven. Press the

"CANCEL" pad.

Press the "Lower Oven" pad and repeat the steps

you completed for checking the upper oven.

If your oven does not heat or an "F", foibwed

by a number,

appears in the display,

contact

your dea_er or check the "ff you need service..."

section

of this Installation

_nstructions.

To get the most efficient use

from your new oven, read your

Use and Care Guide. Keep installation

hstructions

and Guide cmoseto oven

for easy reference.

Page 3