KitchenAid KEBC149BSS0 Panduan Petunjuk Instalasi - Halaman 4
Jelajahi secara online atau unduh pdf Panduan Petunjuk Instalasi untuk Oven KitchenAid KEBC149BSS0. KitchenAid KEBC149BSS0 16 halaman. 24" (60 cm) electric built-in oven
Halaman Cetak
Ifcodes permit and a separate ground w ire isused, i tis
recommended
thataqualified electrical installer determine that
theground p athand thewire gauge areinaccordance withlocal
codes.
Check w ithaqualified electrical installer ifyouarenotsure the
oven isproperly grounded.
This oven must b econnected toagrounded metal, permanent
wiring system.
Besure thattheelectrical connection andwire size areadequate
andinconformance
withtheCSA Standards C22.1-94, Canadian
Electrical Code, Part 1 andC22.2 No. O -M91-1atest
edition, and
alllocal c odes a ndordinances.
Models r ated 3.6kWandbelow at120/240 volts require a
separate 15-amp c ircuit. Models r ated 3.6to4.8kWat
120/240 volts require a separate 20-amp c ircuit.
Acircuit b reaker isrecommended.
Connect directly t othecircuit b reaker box(orfused
disconnect) through f lexible, armored ornonmetallic
sheathed, copper cable (with grounding wire). See "Make
Electrical Connection" section.
CSA approved flexible c onduit from theoven should b e
connected directly t othejunction b ox.
Fuse bothsides o ftheline.
Acopy oftheabove c ode standards canbeobtained from:
Canadian Standards Association
178Rexdale Blvd.
Toronto, ONM9W 1R3 CANADA
Electrical
Connection
To properly install your oven, you must determine the type of
electrical connection you will be using and follow the instructions
provided for it here.
•
Oven must be connected to the proper electrical voltage and
frequency as specified on the model/serial number rating
plate. The model/serial
number rating plate is on the right
vertical part of the oven frame. See the following illustration.
•
Do not cut the conduit. The length of conduit provided is for
serviceability of the oven.
•
A CSA approved conduit connector must be provided.
•
If the house has aluminum wiring, follow the procedure
below:
1. Connect a section of solid copper wire to the ends of the
CSA approved flexible conduit leads.
2. Connect the aluminum wiring to the added section of
copper wire using special connectors
and/or tools
designed for joining copper to aluminum.
Follow the electrical connector manufacturer's
recommended
procedure. Aluminum/copper
connection must conform with
local codes and industry accepted wiring practices.
A. Model/serial number plate
INSTALLATION INSTRUCTIONS
s "_','__"s
0_,%
_/%
1. Decide on the final location for the oven. Avoid drilling or
cutting into house wiring during installation.
Excessive
Weight Hazard
Use two or more people to move and install oven.
Failure to do so can result in back or other injury.
2. To avoid floor damage, set the oven onto cardboard prior to
installation. Do not use handle or any portion of the front
frame for lifting.
3. Remove the shipping materials and tape from the oven.
4. Remove the hardware package from inside the bag
containing
literature.
5. Remove and set aside racks and other parts from inside the
oven.
6. Move oven and cardboard close to the oven's final location.
e_
_"sove
D
IMPORTANT:
Use both hands to remove oven doors.
1. Open oven door all the way.
2. Flip up the hinge latch on each side.
3. Close the oven door as far as it will shut.
4. Lift the oven door while holding both sides.
Continue to push the oven door closed and pull it away from
the oven door frame.