KitchenAid KEBC177KBT0 Petunjuk Instalasi - Halaman 4
Jelajahi secara online atau unduh pdf Petunjuk Instalasi untuk Oven KitchenAid KEBC177KBT0. KitchenAid KEBC177KBT0 5 halaman. 27" electric built-in single and double ovens
Halaman Cetak
Electrical connection
If your house has aluminum wiring, see
"Electrical requirements", Page 2.
Electrical Shock Hazard
Turn power supply off before connecting wires.
Use 8 gauge solid copper wire.
Electrically ground range.
Failure to follow these instructions can result
in death, fire, or electrical shock.
This oven is manufactured with white {neutral)
power supply wire and a cabinet=connected bare
grounding wire twisted together.
Feed oven cable through opening in
the cabinet. Make electrical connection
foUUowing the steps needed for your instaUUation.
1. Disconnect the power supply.
2. Remove the junction box cover.
3. Connect oven cable to junction box through the
U.L.qisted conduit connector.
4. Connect the two black wires together with
twist-on connectors.
5. Connect the two red wires together with
twist-on connectors.
8. Complete electrical connection according to
local codes and ordinances.
cable from
iunetion
power
suppl,/
box _
white _
c>_
w,re _
_>_/¢"
grounding
oven
cable wires
--
factory
crimped
Figure 1
cable from
oven
conduit
connector
if local codes PERMIT
connectingcabinet-grounding
conductor
to neutral white
wire in junction
box:
7. Connect the fac:tory°crimped
bare and white oven cable wires
to the neutral
(white) wire in
junction
box. See Figure 1.
8. Replace junction
box cover.
eabb from
iunetion
power supph!
Figure 2
eabte from
connector
oven
ff local codes DO NOT PERMIT
connecting
cabinet-grounding
conductor
to neutral white
wire in junction
box:
7. Separate the factory-crimped
bare and white oven cable wires.
8. Connect white oven cable wire to
neutral (white) wire in junction
box. See Figure 2.
9. Connect the bare grounding
oven cable wire to a grounded
wire in the junction box. See
Figure 2.
lg. Replace junction box cover.
ff connecting
to a
four-wire electrical system:
7. Separate bare and white oven
cable wires.
8. Connect white oven cable wire
to neutral (white) wire in
junction box. See Figure 2.
9. Connect the bare grounding
oven cable wire to the green
grounding wire in junction box.
Do Not connect hare grounding
wire to neutral (white} wire in
junction box. See Figure 2.
10. Replace junction box cover.
Attachment
Carefully push against seal area of oven front
frame when pushing oven into cabinet.
Do Not push against outside edges,
rt
i'
5m
Lift oven into cabinet cutout using the
oven opening as an area to grip.
6u
Important:
Securely fasten oven to cabinet
using the screws provided
(two screws for a single
oven or four screws for a double oven), Insert the
screws through
hobs in mounting
rails, Do Not
overtighten
screws.
screws
8u
Replace oven racks.
important: Replace the door with the model/serial
rating plate on the upper oven.
On some models, the construction of this door is
designed to withstand self-cbaning
temperatures.
Reinstall the oven door by inserting ends
of hinges into hinge slots in the oven frame. Push
hinges in as far as they will go. Open the door
(you wiii feel the door drop into place} and rotate
both hinge latches back to the locked position.
Close and open the door to check that the door
closes and opens completel% If door does not
dose or open completely, repeat the door
removal step and reinstall door as described
above.
Repeat for lower oven door.
shipping
foot
Push against seal area of front frame to push
oven into cabinet until shipping
feet almost
contact cabineL Use a Phillips screwdriver
to
remove screws attaching
shipping
feet. Remove
and discard shipping
feet.
Push oven completely
into cabinet and center
oven in cabinet cutout.
Slide top
of trim up.
Push trim
:_
into prance.
Replace
trim screw.
7m
Slide top end of each trim upward onto oven
side rails. Push each trim into place at bottom of
trim. Use screws to attach each trim to oven. Take
care not to scratch other surfaces with ends of trim.
Check operation
O
m Turn on power supply. The display
panel wili light up briefly. "PF" should appear in
the temperature display.
the display. Press the "START" pad. Make sure the
oven door is closed and the "ON" light is shown in
the display area. After 2 minutes, partially open
oven door. You should feel heat from the oven.
Press the "CANCEL" pad.
Check the operation of your doubte oven.
Press the "Upper Oven" pad. Press the "BROIL"
pad. "BROIL" will appear in the display. Press the
"START" pad. Make sure the oven door is closed
and the "ON" light is shown in the display area.
After 2 minutes, partially open oven door. You
should feel heat from the oven. Press the
"CANCEL" pad.
Press the "Lower Oven" pad and repeat the steps
you completed for checking the upper oven.
tf your oven does not heat or an "F,
followed
by a number,
appears in the display,
contact
your dealer or check the "If you need service..."
section of this Installation
Instructions.
To get the most efficient use
from your new oven, read 7our
Use and Care Guide. Keep Installation
mnstructions
and Guide close to oven
for easy reference.
Page 3