KitchenAid KEBS209E Panduan Petunjuk Instalasi - Halaman 6
Jelajahi secara online atau unduh pdf Panduan Petunjuk Instalasi untuk Oven KitchenAid KEBS209E. KitchenAid KEBS209E 16 halaman. 27" (68.6 cm) and 30" (76.2 cm) electric single and double built-in oven
Halaman Cetak
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrical installer determine that
the ground path and the wire gauge are in accordance with local
codes.
Check with a qualified electrical installer if you are not sure the
oven is properly grounded.
This oven must be connected to a grounded metal, permanent
wiring system.
Be sure that the electrical connection and wire size are adequate
and in conformance with the National Electrical Code, ANSI/
NFPA 70-latest edition or CSA Standards C22.1-94, Canadian
Electrical Code, Part 1 and C22.2 No. O-M91-latest edition, and
all local codes and ordinances.
A copy of the above code standards can be obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02169-7471
CSA International
8501 East Pleasant Valley Road
Cleveland, OH 44131-5575
Electrical Connection
To properly install your oven, you must determine the type of
electrical connection you will be using and follow the instructions
provided for it here.
Oven must be connected to the proper electrical voltage and
■
frequency as specified on the model/serial/rating plate. The
model/serial/rating plate is located under the control panel on
single ovens and under the control panel on the upper oven
cavity on double ovens. See the following illustrations.
Single Oven
A. Model/serial/rating plate
6
Electrical Requirements
A
Double Oven
A. Model/serial/rating plate
Models rated from 7.3 to 9.6 kW at 240 volts (5.4 to 7.4 kW at
■
208 volts) require a separate 40-amp circuit. Models rated at
4.8 kW and below at 240 volts (3.6 kW and below at
208 volts) require a separate 20-amp circuit.
A circuit breaker is recommended.
■
Connect directly to the circuit breaker box (or fused
■
disconnect) through flexible, armored or nonmetallic
sheathed, copper cable (with grounding wire). See "Make
Electrical Connection" section.
Flexible conduit from the oven should be connected directly
■
to the junction box.
Fuse both sides of the line.
■
Do not cut the conduit. The length of conduit provided is for
■
serviceability of the oven.
A UL listed or CSA approved conduit connector must be
■
provided.
If the house has aluminum wiring, follow the procedure
■
below:
1. Connect a section of solid copper wire to the ends of the
flexible conduit leads.
2. Connect the aluminum wiring to the added section of
copper wire using special connectors and/or tools
designed and UL listed for joining copper to aluminum.
Follow the electrical connector manufacturer's recommended
procedure. Aluminum/copper connection must conform with
local codes and industry accepted wiring practices.
For power requirements for models KOST107E, KOST100E,
KOSE507E, KOSE500E, KODE307E, KODE300E, KODE507E,
KODE500E, KODT100E and KODT107E, refer to the following
table.
A
Voltage
Single
Thermal
240 VAC 4100 W
208 VAC 3100 W
240 VAC
17.2 A
208 VAC
15.0 A
Single
Double
Double
Convect
Thermal
Convect
4100 W
8300 W
8300 W
3100 W
6300 W
6300 W
17.2 A
34.2 A
34.2 A
15.0 A
29.9 A
29.9 A
Double
Convect/
Thermal
8300 W
6300 W
34.2 A
29.9 A