Makita 6013B Buku Petunjuk - Halaman 3
Jelajahi secara online atau unduh pdf Buku Petunjuk untuk Bor Makita 6013B. Makita 6013B 6 halaman. 13 mm (1/2")
Juga untuk Makita 6013B: Buku Petunjuk (8 halaman), Buku Petunjuk (8 halaman), Buku Petunjuk (20 halaman)
Halaman Cetak
ENGLISH
1 Tighten
2 Chuck key
3 Sleeve
4 Ring
SPECIFICATIONS
Model
Drilling capacities
Steel ...................................................................................................... 13 mm
Wood .................................................................................................... 36 mm
No load speed (RPM) ............................................................................. 550
Overall length .......................................................................................... 340 mm
Net weight ............................................................................................... 2.8 kg
• Due to the continuing program of research and
development, the specifications herein are subject
to change without prior notice.
• Note: Specifications may differ from country to
country.
Power supply
The machine should be connected only to a power
supply of the same voltage as indicated on the
nameplate, and can only be operated on single-phase
AC supply. They are double-insulated in accordance
with European Standard and can, therefore, also be
used from sockets without earth wire.
Safety hints
For your own safety, please refer to enclosed Safety
instructions.
These symbols mean:
Read instruction manual.
DOUBLE INSULATION
ADDITIONAL SAFETY RULES
1. Always be sure you have a firm footing. Be
sure no one is below when using the machine
in high locations.
2. Hold the machine firmly.
3. Keep hands away from rotating parts.
4. When drilling into walls, floors or wherever
''live'' electrical wires may be encountered. DO
NOT TOUCH ANY METAL PARTS OF THE
MACHINE! Hold the machine by the insulated
grasping surfaces to prevent electric shock if
you drill into a ''live'' wire.
5. Do not leave the machine running. Operate the
machine only when hand-held.
6. Do not touch the drill bit or the workpiece
immediately after operation; they may be
extremely hot and could burn your skin.
SAVE THESE INSTRUCTIONS.
Explanation of general view
5 Switch trigger
6 Lock button
7 Counterclockwise
8 Clockwise
OPERATING INSTRUCTIONS
Installing top grip (auxiliary handle) (Fig. 1)
Screw the top grip on the machine securely.
Installing or removing drill bit
Important:
Always be sure that the machine is switched off and
unplugged before installing or removing the bit.
For machines with standard keyed chuck (Fig. 2)
To install the bit, place it in the chuck as far as it will
go. Tighten the chuck by hand. Place the chuck key in
each of the three holes and tighten clockwise. Be sure
to tighten all three chuck holes evenly.
To remove the bit, turn the chuck key counterclock-
wise in just one hole, then loosen the chuck by hand.
After using the chuck key, be sure to return it to the
original position.
For machines with keyless chuck (Fig. 3)
Hold the ring and turn the sleeve counterclockwise to
open the chuck jaws. Place the bit in the chuck as far
as it will go. Hold the ring firmly and turn the sleeve
clockwise to tighten the chuck. To remove the bit, hold
the ring and turn the sleeve counterclockwise.
Switch action
CAUTION:
• Before plugging in the machine, always check to
see that the switch trigger actuates properly and
returns to the ''OFF'' position when released.
• Change the direction of rotation only after the
machine comes to a complete stop. Changing it
before the machine stops may damage the
machine. (Model 6013BR only)
Model 6013B (Fig. 4)
To start the machine, simply pull the trigger. Release
the trigger to stop. For continuous operation, pull the
trigger and then push in the lock button. To stop the
machine from the locked position, pull the trigger fully,
then release it.
9 Limit mark
0 Brush holder cap
q Screwdriver
6013B
6013BR
13 mm
36 mm
550
340 mm
2.8 kg
3