Gardena V1 Panduan Operator - Halaman 8

Jelajahi secara online atau unduh pdf Panduan Operator untuk Sistem irigasi Gardena V1. Gardena V1 11 halaman. Valve box
Juga untuk Gardena V1: Panduan Petunjuk Pengoperasian (6 halaman), Panduan Petunjuk Pengoperasian (10 halaman), Panduan Petunjuk Pengoperasian (9 halaman)

Halaman Cetak

1. SAFETY

IMPORTANT!

Read the operator's manual carefully before use and keep for future

reference.

WINTER STORAGE!

Read the notes on safety in the Valve Box.

Before the frost period starts: see 3. STORAGE

To put into storage / Winter storage.

Please observe the notes on safety in the operating

instructions.

2. ASSEMBLY

A video on how

to assemble the

V3 Valve Box can

be found here:

Note: Assemble the screw connections for all parts by hand;

do not use tools.

(Fig. 1) Grease all O-rings and metal securing clips with accompany-

ing silicone grease.

(Fig. 2.1) The distributor (C) has three connections. Screw end

caps (D) onto the unused distributor inputs.

(Fig. 2.2 – 2.5) Insert the distributor and connections (G) and secure

with the nuts (E). Fit the drain cap (F).

(Fig. 3) Insert the long telescopic pipe (I) into the connection on the

outlet side (securing clip facing upwards).

(Fig. 4) Screw the short telescopic pipe (J) into the input side of the

valve. Arrows on valve show the direction of flow.

(Fig. 5.1) Insert the valve with the short telescopic pipe into the input

side of the box.

(Fig. 5.2) Screw the long telescopic pipe (I) into the outlet side of the

valve (I).

(Fig. 5.3 + 5.4) Press down the securing clips. If necessary, screw in

the telescopic pipes until such point as the clips move down without

much resistance.

(Fig. 6) Insert a short telescopic pipe (J) into the open distributor

outlet on any channels that are not needed.

(Fig. 7) Underlay the valve box with a pack of coarse gravel and set it

in place so that it is level with the turf.

V1: min. 20 x 30 x 10 cm; V3: min. 35 x 30 x 10 cm

(Fig. 8) If connecting a number of valve boxes, use suitable connec-

tors as per illustration.

Tip: When using more than one valve box, screw them

sidebyside onto a wooden board to secure them.

3. STORAGE

To put into storage / Winter Storage:

The following precautions must be taken – especially

before the frost period starts – to prevent damage to the

Irrigation Valves:

1. Close the water tap and disconnect the hose from the GARDENA

Water Connection Point Art. 2722.

2. If the watering system is directly connected to the water tap, turn off

the water supply and open the venting tap.

3. Set the selection lever (Fig. 12) a of all valves to the "ON" position.

4. Draining the Irrigation Valve / Valve Box.

There are various ways to drain the system:

• Drain the system by blowing out the water with compressed

air.

• Remove all the valves and store in a place protected from

frost.

A video on how

to install the

valves can be

found here:

DANGER!

This product makes an electromagnetic field while it operates. This field

may under some conditions interfere with active or passive medical

implants. To decrease the risk of conditions that can possibly injure or

kill, we recommend persons with medical implants to speak with their

physician and the medical implant manufacturer before you operate the

product.

DANGER!

Small parts can be easily swallowed. There is also a risk that the poly-

bag can suffocate toddlers. Keep toddlers away when you assemble the

product.

(Fig. 9) Insert the terminal strip (N) into the bracket.

(Fig. 10) Connection from 1 V3 Valve Box to 3 24V valves:

• For better mapping, label the valves using the yellow, numbered

stickers (1 – 15).

• Strip the individual cables of the connection cable (7 x 0.5 mm

Art. 1280) and connect with terminals 1, 2, 3 on the water control

and the V3 Valve Box. Connect another individual cable to the

terminal (C) on the water control and the V3 Valve Box.

• Connect a cable from each of the valves 1, 2 and 3 to terminals

1, 2 and 3 on the valve box. Connect the second cable of the valves

to the terminals (C) in the valve box.

Connecting a further V3 Valve Box with 3 valves:

• Connect the cable to terminals 4, 5, 6 on the water control and the

first V3 Valve Box.

• Connect a cable from each of valves 4, 5 and 6 to terminals

4, 5 and 6 on the second valve box. Connect the second cable of

valves 4, 5 and 6 to the terminals (C) in the second valve box.

• Use a short length of cable to connect terminals 4, 5, 6 and C on the

first valve box to terminals 4, 5, 6 and C on the second valve box.

(Fig. 11) Press the protective cap (O) over the terminal strip (N) and

secure using the two screws (M).

(Fig. 12) Setting the valve controls:

Fully automatic control:

• Set selection lever to "AUTO / OFF".

Program-controlled water flow to watering system as per program-

ming on water control.

An automatically opened valve cannot be manually closed on

the valve.

Manual control:

• Set selection lever to "ON".

Permanent water flow, independent of programming.

(Fig. 13) To protect against theft, the lid can be secured with a small

padlock or hasp (not included).

• With Valve Box V3, open the draining cap (F) and empty the

supply line. You can leave the Watering Valves in the Valve

Box provided that the lines leading from the Valve Box V3

are drained via a draining valve (e. g. in the GARDENA Popup

Sprinklers) that is installed lower than the Watering Valve.

5. Remove the battery from the Control Unit.

6. Lock the box lid (Fig. 13.3).

Disposal:

(in accordance with RL2012/19/EC)

The product must not be disposed of to normal household

waste. It must be disposed of in line with local environmental

regulations.

IMPORTANT! Dispose of the product through or via your

municipal recycling collection centre.