Makita 6213D Buku Petunjuk - Halaman 5

Jelajahi secara online atau unduh pdf Buku Petunjuk untuk Bor Makita 6213D. Makita 6213D 10 halaman.
Juga untuk Makita 6213D: Manual (12 halaman)

Halaman Cetak

ADDITIONAL SAFETY RULES FOR TOOL

Be aware that this tool is always in an operating

condition, because it does not have to be

plugged into an electrical outlet.

Hold tool by insulated gripping surfaces when

performing an operation where the cutting tool

may contact hidden wiring. Contact with a "live"

wire will also make exposed metal parts of the

tool "live" and shock the operator.

Always be sure you have a firm footing.

Be sure no one is below when using the tool in

high locations.

Hold the tool firmly.

Keep hands away from rotating parts.

Do not leave the tool running. Operate the tool

only when hand-held.

Do not touch the drill bit or the workpiece imme-

diately after operation; they may be extremely

hot and could burn your skin.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing battery cartridge (Fig. 1)

• Always switch off the tool before insertion or removal of

the battery cartridge.

• To remove the battery cartridge, withdraw it from the

tool while pressing the buttons on both sides of the car-

tridge.

• To insert the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Always insert it all the way until it locks in

place with a little click. If not, it may accidentally fall out

of the tool, causing injury to you or someone around

you.

• Do not use force when inserting the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

Installing or removing driver bit or drill bit

(Fig. 2 & 3)

Important:

Always be sure that the tool is switched off and the bat-

tery cartridge is removed before installing or removing

the bit.

Hold the ring and turn the sleeve counterclockwise to

open the chuck jaws. Place the bit in the chuck as far as it

will go. Hold the ring firmly and turn the sleeve clockwise

to tighten the chuck.

To remove the bit, hold the ring and turn the sleeve coun-

terclockwise. When not using the driver bit, keep it in the

bit holders. Bits 45 mm long can be kept there.

Switch action (Fig. 4)

CAUTION:

ENB022-1

Before inserting the battery cartridge into the tool, always

check to see that the switch trigger actuates properly and

returns to the "OFF" position when released.

To start the tool, simply pull the trigger. Tool speed is

increased by increasing pressure on the trigger. Release

the trigger to stop.

Reversing switch action (Fig. 5)

CAUTION:

• Always check the direction of rotation before operation.

• Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation

before the tool stops may damage the tool.

This tool has a reversing switch to change the direction of

rotation. Depress the reversing switch lever from the A

side for clockwise rotation or from the B side for counter-

clockwise rotation. When the switch lever is in the neutral

position, the switch trigger cannot be pulled.

Speed change (Fig. 6)

To change the speed, first switch off the tool and then

slide the speed change lever to the "II" side for high

speed or "I" side for low speed. Be sure that the speed

change lever is set to the correct position before opera-

tion. Use the right speed for your job.

CAUTION:

• Always set the speed change lever fully to the correct

position. If you operate the tool with the speed change

lever positioned half-way between the "I" side and "II"

side, the tool may be damaged.

• Do not use the speed change lever while the tool is run-

ning. The tool may be damaged.

Adjusting the fastening torque (Fig. 7)

The fastening torque can be adjusted in 18 steps by turn-

ing the adjusting ring so that its graduations are aligned

with the pointer on the tool body. The fastening torque is

minimum when the number 1 is aligned with the pointer,

and maximum when the

pointer.

The clutch will slip at various torque levels when set at

the number 1 to 5. The clutch is designed not to slip at

the

marking. Before actual operation, drive a trial screw

into your material or a piece of duplicate material to

determine which torque level is required for a particular

application.

NOTE:

• The adjusting ring does not lock when the pointer is

positioned only half-way between the graduations.

• Do not operate the tool with the adjusting ring set

between the number 5 and the

be damaged.

marking is aligned with the

marking. The tool may