Gardena ErgoJet 2500 Panduan Petunjuk Pengoperasian - Halaman 3
Jelajahi secara online atau unduh pdf Panduan Petunjuk Pengoperasian untuk Blower Gardena ErgoJet 2500. Gardena ErgoJet 2500 17 halaman. Electric blower/vac
Juga untuk Gardena ErgoJet 2500: Panduan Petunjuk Pengoperasian (18 halaman), Panduan Petunjuk Pengoperasian (19 halaman), Panduan Petunjuk Pengoperasian (19 halaman), Panduan Petunjuk Pengoperasian (10 halaman), Panduan Petunjuk Pengoperasian (9 halaman), Panduan Operator (8 halaman)
Halaman Cetak
Use only with fully
installed suction tube
and covered collection
bag in suction mode.
General Power Tool Safety Warnings
WARNING
warnings and all instructions.
Failure to follow the warnings and
instructions may result in electric
shock, fire and/or serious injury.
Save all warning and instructions for future
reference.
The term "power tool" in the warnings refers to
your mains operated (corded) power tool.
1) Work area safety
a) This product is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or instruc
tion concerning the use of the product by
a person responsible for their safety. Children
should be supervised to ensure that they do
not play with the product. Local regulations
may restrict the age of the operator. Never
allow children or people unfamiliar with these
instructions to use the product. Power tools
are dangerous in the hands of untrained users.
b) Never operate the product while people,
especially children, or pets are nearby.
Distractions can cause you to lose control.
c) Never blow debris in the direction of
bystanders. The operator or user is responsible
for accidents or hazards occurring to other
people or their property.
d) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
e) Do not operate power tools in explosive
atmospheres, such as in the presence of flam
mable liquids, gases or dust. Power tools create
sparks which may ignite the dust or fumes.
2) Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do not use
any adaptor plugs with earthed (grounded)
power tools. Use only on AC mains supply
voltage shown on the product rating label.
Unmodified plugs and matching outlets will
reduce risk of electric shock.
: Read all safety
Wait until the rotor
blades have stopped
moving after switching
off.
Do not use when wear
ing open hair, loose
jewellery or loosefitting
clothes.
b) Avoid body contact with earthed or ground
ed surfaces, such as pipes, radiators, ranges
and refrigerators. There is an increased risk of
electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk electric shock.
d) Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp
edges or moving parts. Before use, examine
cord for damage. Replace cord if there
are signs of damage or ageing. Do not use
the product if the cord is damaged or worn.
Immediately disconnect from the mains
electricity supply if the cord is cut, or the
insulation is damaged. Do not touch the
electric cord until the electrical supply has
been disconnected. Do not repair a cut or
damaged cord. Replace it with a new one.
Damaged or entangled cords increase the risk
of electric shock.
e) The electric cord must be uncoiled.
Coiled cord can overheat and reduce the
efficiency of the product. Always wind cord care-
fully, avoiding kinks.
f) When operating a power tool outdoors,
use an extension cord suitable for outdoor
use fitted with a coupler according to
IEC 6032023. Use of a cord suitable for
outdoor use reduces the risk of electric shock.
g) If operating a power tool in a damp
l ocation is unavoidable, use a residual
current device (RCD) protected supply
with a tripping current of not more than
30 mA. Even with a RCD installed,
100% safety cannot be guaranteed and
safe working practices must be followed
at all times. Check your RCD every time
you use your product. Use of an RCD
reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and
use common sense when operating a power
tool. Do not use a power tool while you are
tired or under the influence of drugs, alcohol
or medication. A moment of inattention while
17