Align-Pilates C2-Pro Petunjuk Perakitan & Panduan Pengguna - Halaman 3
Jelajahi secara online atau unduh pdf Petunjuk Perakitan & Panduan Pengguna untuk Peralatan Kebugaran Align-Pilates C2-Pro. Align-Pilates C2-Pro 12 halaman. Reformer
Halaman Cetak
After removing the reformer frame from the packaging the first job is to assemble the foot
bar:
a) Carefully cut off the cable ties holding the foot bar in the folded position.
b) With the aid of another person lift up the standing platform end of the reformer and
swing the foot bar out from under the machine.
c) Cut off the cable ties holding the chrome Gear bar (#26 - see exploded diagram on
page 10) and position it in the 2nd slot away from the end of the reformer.
d) Now bolt the Foot bar Selector bar to the chrome Gear bar from the outside
using the M8 20mm bolt (#103) . Now repeat on the other side, but do not fully
tighten. See Fig. 1.
e) Now insert the M8 x 15mm dome headed bolt (#92) from the inside and fully tighten.
Repeat on the other side. See Fig. 2
f) Now fully tighten all four bolts
Note: at this point if you have only ordered the C2–Pro, without the extension legs please
jump to section 3 in the manual.
2. Attaching the Leg Extensions (optional extra)
If you bough the option leg height extensions now is a good time to attach them. We recommend you get a pair of
stable trestles to put the reformer on to enable easy fitting of the legs. Ensuring the trestles have something soft on
them to avoid scratching the frame, lift the reformer out of the box and place it gently onto the trestles, so one of the
trestles is underneath the point where the foot bar attaches to the aluminium runner and the other is near the rope riser
end.
Remove the wheels at the foot end of the reformer, placing all nuts, bolts and washers to one side. Store the parts in
the order you removed them and then reinstall the wheels on to the higher legs. Remove all four of the black
adjustable screw in feet by unscrewing them completely out and then screw these completely in to the C2-Pro leg
extensions.
Using the allen bolts and a 6mm Allen key, screw in the 5 bolts per leg and hand tighten. Be careful not to cross thread
the bolts. Once all the bolts are in, tighten fully with the Allen key. After removing your trestles or other elevation device,
put your reformer down where you intend to use it. Then use a spirit level to check the reformer is level and stable. Ad-
just the level of the reformer by turning the rubber feet in or out. The parts list and exploded diagram is shown in Fig.3
for your reference.
3. Insert the Reformer Carriage
With the reformer back on the floor, firstly remove the 2 rubber carriage stoppers from the end of the runners (Fig. 6),
now carefully remove the carriage from its packaging. Note that two of the wheels are on floating axles wheels that
allow the carriage to self-center, aiding the smooth running of the reformer - be careful not to tip the carriage or these
wheels can slide out (Fig 4). With one person holding each side of the carriage gently slide the carriage in to the run-
ners (Fig. 5) with the springs pointing towards the standing platform, care must be taken to align the floating wheels
with the C shape runner channel when inserting the carriage in to the runners to prevent damage to the wheels. Note
when removing the carriage for maintenance be careful not to let the wheels fall out!
Fig.4
Fig.1
Fig.2
Ref
Code
Name
1
1L
Left leg standing platform end
2
1R
Right leg standing platform end
3
2R
Right leg rope riser end
4
2L
Left leg rope riser end
5
Flat washer
6
Spring washer
7
Bolt
Fig.5
Fig.3
Specification
Qty
1
1
1
1
8.5*20*T1.5
20
8.3*12.7*T2.0
20
M8*20
20
3