Garmin 010-01338-2A Panduan Pemilik - Halaman 21
Jelajahi secara online atau unduh pdf Panduan Pemilik untuk Menonton Garmin 010-01338-2A. Garmin 010-01338-2A 28 halaman. Gps watch garmin fenix 3
Halaman Cetak
The Garmin logos should be right-side up.
4
Bring the device within 3 m (10 ft.) of the heart rate monitor.
After you put on the heart rate monitor, it is active and sending
data.
TIP: If the heart rate data is erratic or does not appear, see the
troubleshooting tips
(Tips for Erratic Heart Rate
Tips for Erratic Heart Rate Data
If the heart rate data is erratic or does not appear, you can try
these tips.
• Reapply water to the electrodes and contact patches.
• Tighten the strap on your chest.
• Warm up for 5–10 minutes.
• Follow the care instructions
Monitor).
• Wear a cotton shirt or thoroughly wet both sides of the strap.
Synthetic fabrics that rub or flap against the heart rate
monitor can create static electricity that interferes with heart
rate signals.
• Move away from sources that can interfere with your heart
rate monitor.
Sources of interference may include strong electromagnetic
fields, some 2.4 GHz wireless sensors, high-voltage power
lines, electric motors, ovens, microwave ovens, 2.4 GHz
cordless phones, and wireless LAN access points.
Using an Optional Bike Cadence Sensor
You can use a compatible bike cadence sensor to send data to
your device.
• Pair the sensor with your device
• Update your fitness user profile information
User
Profile).
• Go for a ride
(Going for a
Foot Pod
Your device is compatible with the foot pod. You can use the
foot pod to record pace and distance instead of using GPS when
you are training indoors or when your GPS signal is weak. The
foot pod is on standby and ready to send data (like the heart
rate monitor).
After 30 minutes of inactivity, the foot pod powers off to
conserve the battery. When the battery is low, a message
appears on your device. Approximately five hours of battery life
remain.
Foot Pod Calibration
The foot pod is self-calibrating. The accuracy of the speed and
distance data improves after a few outdoor runs using GPS.
Calibrating Your Foot Pod Manually
Before you can calibrate your device, you must pair your device
with the foot pod
(Pairing ANT+
Manual calibration is recommended if you know your calibration
factor. If you have calibrated a foot pod with another Garmin
product, you may know your calibration factor.
1
Hold UP.
2
Select Settings > Sensors > Foot Pod > Cal. Factor.
3
Adjust the calibration factor:
• Increase the calibration factor if your distance is too low.
• Decrease the calibration factor if your distance is too high.
tempe
The tempe is an ANT+ wireless temperature sensor. You can
attach the sensor to a secure strap or loop where it is exposed
to ambient air, and therefore, provides a consistent source of
Device Information
Data).
(Caring for the Heart Rate
(Pairing ANT+
Sensors).
(Setting Up Your
Ride).
Sensors).
accurate temperature data. You must pair the tempe with your
device to display temperature data from the tempe.
Device Information
Viewing Device Information
You can view the unit ID, software version, and license
agreement.
1
Hold UP.
2
Select Settings > System > About.
Device Care
Do not use a sharp object to clean the device.
Avoid chemical cleaners, solvents, and insect repellents that can
damage plastic components and finishes.
Thoroughly rinse the device with fresh water after exposure to
chlorine, salt water, sunscreen, cosmetics, alcohol, or other
harsh chemicals. Prolonged exposure to these substances can
damage the case.
Avoid pressing the keys under water.
Avoid extreme shock and harsh treatment, because it can
degrade the life of the product.
Do not store the device where prolonged exposure to extreme
temperatures can occur, because it can cause permanent
damage.
Cleaning the Device
Even small amounts of sweat or moisture can cause corrosion
of the electrical contacts when connected to a charger.
Corrosion can prevent charging and data transfer.
1
Wipe the device using a cloth dampened with a mild
detergent solution.
2
Wipe it dry.
After cleaning, allow the device to dry completely.
Metal Watch Band Adjustment
If your watch includes a metal watch band, you should take your
watch to a jeweler or other professional to adjust the length of
the metal band.
Specifications
Battery type
Battery life
Water rating
Operating temperature range From -20º to 55ºC (from -4º to 131ºF)
Charging temperature range From 0º to 45ºC (from 32º to 113ºF)
Radio frequency/protocol
*The device withstands pressure equivalent to a depth of 100 m.
For more information, go to www.garmin.com/waterrating.
Battery Information
The actual battery life depends on the features enabled on your
device, such as activity tracking, smartphone notifications, GPS,
internal sensors, and connected ANT+ sensors.
Battery Life Mode
Up to 20 hr.
Normal GPS mode
Up to 50 hr.
UltraTrac GPS mode with two-minute polling interval
Up to 6 wk.
Watch mode
NOTICE
NOTICE
Rechargeable, built-in lithium-ion battery
Up to 6 wk.
10 ATM*
2.4 GHz ANT+ wireless technology
Bluetooth Smart device
17