Garmin FORETREX 701 BALLISTIC EDITION Panduan Pemilik - Halaman 5
Jelajahi secara online atau unduh pdf Panduan Pemilik untuk Menonton Garmin FORETREX 701 BALLISTIC EDITION. Garmin FORETREX 701 BALLISTIC EDITION 18 halaman. Ballistic edition
Juga untuk Garmin FORETREX 701 BALLISTIC EDITION: Panduan Pemilik (30 halaman)
Halaman Cetak
- 1. Table of Contents
- 1. Introduction
- 1. Status Icons
- 2. Waypoints, Routes, and Tracks
- 2. Creating a Waypoint
- 2. Viewing Track Details
- 2. Customizing the Range Card Fields
- 2. Editing the Muzzle Velocity and Temperature Table
- 2. Jumpmaster
- 3. Device Information
- 3. Viewing Device Information
- 4. Troubleshooting
- 5. Appendix
- 6. Appendix
- 6. Applied Ballistics Glossary of Terms
- 7. Index
Introduction
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
Device Overview
Battery cover D-ring
Micro-USB port (under battery cover)
Installing the Batteries
You can use alkaline, NiMH, or lithium AAA batteries. Use NiMH
or lithium batteries for best results.
1
Loosen the fabric strap that covers the battery door.
2
Turn the D-ring counter-clockwise, and pull up to open the
battery door.
3
Insert two AAA batteries, observing polarity.
NOTE: You should verify the gasket and battery
compartment are free of debris.
4
Close the battery door, and turn the D-ring clockwise.
Long-Term Storage
When you do not plan to use the device for several months,
remove the batteries. Stored data is not lost when batteries are
removed.
Attaching the Wrist Strap
1
Insert the strap behind the pin
2
Pull the strap length through to the end.
3
Insert the strap behind the pin
4
If necessary, attach the strap extender to the wrist strap.
Introduction
WARNING
at the top of the device.
at the bottom of the device.
Keys
Hold to turn the device on and off, enter night vision mode,
and enter watch mode.
POWER
Select to turn the backlight on and off.
Select to scroll through the main pages in sequence.
PAGE
Hold to navigate to a waypoint.
GOTO
Select to open the menu for the page.
ENTER
Hold to mark a waypoint.
MARK
Select to scroll through menus and pages.
Select to zoom out or zoom in on the map page.
Turning On the Device
Hold POWER.
The first time you turn on the device, you will select the
device language.
Acquiring Satellite Signals
Before you can use GPS navigation features, you must acquire
satellite signals.
When you turn on your navigation device, the GPS receiver
must collect satellite data and establish the current location. The
time required to acquire satellite signals varies based on several
factors, including how far you are from the location where you
last used your navigation device, whether you have a clear view
of the sky, and how long it has been since you last used your
navigation device. The first time you turn on your navigation
device, it may take several minutes to acquire satellite signals.
1
Turn on the device.
2
Wait while the device locates satellites.
It may take 30 to 60 seconds to acquire satellite signals.
3
If necessary, go to an open area, away from tall buildings and
trees.
Using the Backlight
1
Select POWER.
The backlight turns on for 30 seconds.
2
Select POWER to turn off the backlight.
Main Pages
You can select PAGE to scroll through the main pages. You can
select ENTER to open the settings menu for each page. You
can select
or
to scroll through menus and pages and zoom
in and out.
Map page: The map page shows your position and heading on
the map
(Map Page, page
As you travel, the position icon moves and leaves a track log
(trail). Waypoint names and symbols appear on the map. The
device automatically rotates the map as you move so that
waypoints always appear above your position.
Compass page: The compass page guides you to your
destination by displaying a compass and bearing pointer.
When navigating, the compass page displays the name of
the location, the distance to the final destination, the speed of
2).
1