Garmin GPS 17HVS - Receiver Module Panduan Petunjuk Instalasi - Halaman 5
Jelajahi secara online atau unduh pdf Panduan Petunjuk Instalasi untuk Sistem GPS Kelautan Garmin GPS 17HVS - Receiver Module. Garmin GPS 17HVS - Receiver Module 12 halaman. Declaration of conformity
Juga untuk Garmin GPS 17HVS - Receiver Module: Spesifikasi Teknis (34 halaman), Panduan Instalasi (16 halaman), Spesifikasi Teknis (40 halaman), Spesifikasi Teknis (37 halaman), Pernyataan Kesesuaian (2 halaman)
Halaman Cetak
Flush Mount
Tools
• Flush Mount Template
• Jig saw
• Masking tape
• Scissors
• Drill
• Drill bits—1/8" (3 mm) and 3/8" (6 mm)
• 1/16" (2 mm) Allen (Hex) wrench
• Sockets or wrenches
• Hammer
• Center punch
To flush mount the GPSMAP 2006C/2010C:
1. Trim the Flush Mount Template and tape it in the location you want.
2. Using the center punch, indent the center of each mounting hole location.
3. Using an 1/8" (3 mm) drill bit, drill the four mounting holes.
4. Using a 3/8" (6 mm) drill bit, drill a hole for a location to begin cutting the mounting surface.
5. Using the Jig Saw, cut the mounting surface along the inside of the dashed line indicated on the template. Use a file and sandpaper to
refine the size of the hole. Be very careful when cutting this hole. There is only a small amount of clearance between the case
molding and the mounting holes.
6. Install the four mounting studs into unit by screwing the shorter, threaded section into the back of the unit. Use a 1/16" (2 mm) Allen
wrench to tighten the mounting studs until the stop contacts the case. Be careful not to overtighten as this may damage the
mounting stud! The studs have a reusable thread-locking patch
pre-applied from the factory.
7. Place the unit in position in the cut-out of the mounting surface.
8. Place washers over the mounting studs, then thread on one
hex nut per mounting stud. Tighten all four until the unit is snug
against the mounting surface. Install and tighten the second hex
nut set on all four mounting studs to lock the first set in place.
TRIM TEMPLATE ALONG THIS LINE TO AID FITTING
230mm
GPSMAP 2010/2010C/3010C
CUT MOUNTING SURFACE
ALONG INSIDE OF THIS LINE
Be very careful when cutting this hole,
there is only a small amount of clearance
between the unit and the Mounting Hole.
Flush Mounting the GPS
1. Trim the Flush Mount Template and tape in the desired location.
2. Using the Center Punch, indent the center of each Mounting Hole location.
3. Using an 1/8" (3mm) drill bit, drill the four Mounting Holes. (Drilling the mounting
holes before cutting the hole for the unit will allow for an easier installation.)
4. Using a 3/8" (6mm) drill bit, drill a hole for a location to begin cutting the mounting
UNIT OUTLINE
surface.
5. Using the Jig Saw, cut the mounting surface along the inside of the dashed line
indicated on the template. Be very careful when cutting this hole, there is only a small
amount of clearance between the case molding and the Mounting Holes.
6. Install the four Mounting Studs into unit by screwing the shorter, threaded section
into the back of the unit. Use a 1/16" (2mm) Allen Wrench to tighten the Mounting Studs
until the stop contacts the case. Be careful not to overtighten as this may damage the
Mounting Stud! The studs have a reusable thread-locking patch pre-applied from the factory.
7. Place the unit in position in the cut out of the mounting surface.
8. Place washers over the Mounting Studs, then thread on one Hex Nut per Mounting Stud.
Tighten all four until the unit is snug against the mounting surface.
Install and tighten the second Hex Nut on all four Mounting Studs to lock the first one
in place.
DRILL A 3/8" HOLE.
BEGIN CUTTING HERE
Flush Mount Template
GPSMAP 2006C/2010C & GPS 17
208mm
Flush Mount
Stud
Washer Hex nuts
I
I
NSTALLATION
NSTRUCTIONS
Mounting surface
5