Garmin GPSMAP 3005C Panduan Petunjuk Instalasi - Halaman 5

Jelajahi secara online atau unduh pdf Panduan Petunjuk Instalasi untuk Sistem GPS Kelautan Garmin GPSMAP 3005C. Garmin GPSMAP 3005C 17 halaman. Declaration of conformity
Juga untuk Garmin GPSMAP 3005C: Panduan Referensi Cepat (2 halaman), Panduan Petunjuk Instalasi (10 halaman), Panduan Templat (1 halaman), Referensi Cepat (2 halaman), Pernyataan Kesesuaian (1 halaman)

Halaman Cetak

Garmin GPSMAP 3005C Panduan Petunjuk Instalasi

Flush Mounting the GPSMAP 3005C

Tools

• Flush Mount Template

• Jig saw

• Masking tape

• Scissors

• Drill

• Drill Bits—1/8" (3 mm) and 3/8" (6 mm)

• 1/16" (2 mm) Allen (hex) wrench

• Sockets

• Hammer

• Center punch

To ﬂush mount the GPSMAP 3005C:

1. Trim the Flush Mount Template for ﬁt, and tape it in the preferred location.

2. Using a center punch, indent the center of each mounting hole location.

3. Using an 1/8" (3 mm) drill bit, drill the four mounting holes.

4. Using a 3/8" (6 mm) drill bit, drill a hole for a location and begin cutting the mounting surface.

5. Using the jig saw, cut the mounting surface along the inside of the line indicated on the template. Be very careful when cutting this hole,

because there is 1/8" clearance between the case molding and the mounting holes.

6. Install the four mounting studs into unit by screwing the shorter, threaded section into the back of the unit. Use a 1/16" (2 mm) Allen

Wrench to tighten the mounting studs until the stop contacts the case.

Be careful not to overtighten as this may damage the mounting stud!

The studs have a reusable thread-locking patch pre-applied from the

factory.

7. Place the unit into the cut-out of the mounting surface.

8. Place washers over the mounting studs, then thread on one hex nut per

mounting stud. Tighten all four until the unit is snug against the mounting

surface. Install and tighten the second hex nut set on all four mounting

studs to lock the ﬁrst set in place.

GPSMAP 3005C FLUSH MOUNT TEMPLATE

DRILL THE 1/8" (3 mm)

MOUNTING HOLES

BEFORE CUTTING

CUT MOUNTING SURFACE ON

THE INSIDE OF THIS LINE

Be very careful when cutting. There is 1/8"

clearance between the case and the

mounting stud holes. If the cutout is tight, file

or sand the cutout to obtain the correct fit.

Drill a 3/8"

(6 mm)

hole

to start cut.

GPSMAP 3005C & GPS 17

��

Flush Mounting the GPSMAP 3005C

1. Trim the Flush Mount Template for fit and tape in the desired location.

2. Using a Center Punch, indent the center of each Mounting Hole location.

3. Drill the four Mounting Holes using a 1/8" (3 mm) drill bit.

4. Drill a 3/8" (6 mm) hole for a location to begin cutting the mounting surface.

5. Cut along the inside of the indicated line. Be very careful when cutting this hole,

there is 1/8" clearance between the case molding and the Mounting Holes.

6. Install the four Mounting Studs into the unit by screwing the shorter, threaded section

into the back of the unit. Use a 1/16" (2 mm) Allen Wrench to tighten the Mounting Studs

until the stops contact the case. Do not to overtighten the studs. The studs have a factory

applied thread locking patch.

7. Position the GPSMAP 3005C in the cut out of the mounting surface.

8. Place washers over the Mounting Studs, then thread on one Hex Nut per Mounting Stud.

Tighten all four until the unit is snug against the mounting surface.

Install and tighten the second Hex Nut on all four Mounting Studs to lock the first one

in place.

Flush Mount Template

Stud

��

Washer

NSTALLATION

PAGE

QUIT

ENTER

MARK

ADJ

NAV

MOB

DATA

CNFG

FCTN

FIND

Flush Mount

Mounting Surface

Hex Nuts

NSTRUCTIONS