Garmin GHP 10 Marine Autopilot System Panduan Petunjuk Instalasi - Halaman 4
Jelajahi secara online atau unduh pdf Panduan Petunjuk Instalasi untuk Peralatan Kelautan Garmin GHP 10 Marine Autopilot System. Garmin GHP 10 Marine Autopilot System 48 halaman. Tachometer reference
Juga untuk Garmin GHP 10 Marine Autopilot System: Panduan Memulai Cepat (21 halaman), Panduan Petunjuk Instalasi (26 halaman), Referensi Teknis (42 halaman), Pernyataan Kesesuaian (1 halaman), Referensi (1 halaman)
Halaman Cetak
nMEA 2000 Cables and Connectors
The NMEA 2000 cables connect the CCU and the GHC 10 to the NMEA 2000 network. Use the NMEA 2000 power cable and two
terminators to create a NMEA 2000 network on your boat if one does not exist. For more information on NMEA 2000, see
NMEA 2000 drop cable, 6 ft. (2 m) (×2), Garmin part number: 320-00387-00
NMEA 2000 power cable, Garmin part number: 320-00389-00 (×1)
NMEA 2000 extension cables are available if needed. Contact your local Garmin dealer or Garmin Product Support for ordering
information.
CCu/ECu Interconnect Extension Cables (not Included)
When installing the GHP 10 system, you may need to mount the CCU farther
than 16 ft. (5 m) from the ECU. Garmin offers optional replacement or
extension cables for purchase if this is necessary. Contact your local Garmin
dealer or Garmin Product Support for ordering information.
External tachometer Filter (not Included)
If your tachometer source is a direct alternator connection or other signal larger than 12 Vdc, or if you sporadically receive tachometer
errors, install an external tachometer filter (Garmin part number: 010-11399-00). Contact your local Garmin dealer or Garmin product
support for ordering information.
tools needed
•
Safety glasses
•
Drill and drill bits
•
3
/
in. (90 mm) hole saw
1
2
•
Wrenches
•
Wire cutters/stripers
•
Phillips and flat screwdrivers
•
Cable ties
•
Waterproof wire connectors (wire nuts) or heat-shrink tubing
and a heat gun.
•
Marine sealant
•
Compass (to test for magnetic interference when determining
the best location to install the CCU)
•
Anti-seize lubricant (optional)
note: Mounting screws are provided for the GHC 10, for the CCU, for the ECU, and for the pump. If the provided screws are not
appropriate for the mounting surface, you will need to provide the correct types of screws.
NMEA 2000 T-connector (×3), Garmin part
number: 330-00563-00
NMEA 2000 terminators, male Garmin part
number: 330-00564-00 (×1); female Garmin part
number: 330-00565-00 (×1)
type
type
Replacement
Replacement
Replacement
Replacement
Extension
Extension
Extension
Extension
Extension
Extension
CCu/ECu Interconnect Extension Cables
CCu/ECu Interconnect Extension Cables
•
Hydraulic supplies (Shipyard Supply)
◦
Additional hydraulic hose with machine-crimped or
field-replaceable fittings that have a minimum rating of
1,000 lbf/in
2
◦
Additional hydraulic fluid
◦
Rags
◦
Thread sealant (Loctite® Pro Lock Tight® multipurpose
anaerobic gel, part number 51604 or equivalent)
◦
Helm/hydraulic bleeding equipment
GHP 10 Marine Autopilot System Installation Instructions
Length
Length
Garmin Part number
Garmin Part number
32 ft. (10 m)
32 ft. (10 m)
010-11055-01
010-11055-01
66 ft. (20 m)
66 ft. (20 m)
010-11055-02
010-11055-02
16 ft. (5 m)
16 ft. (5 m)
010-11156-00
010-11156-00
50 ft (15 m)
50 ft (15 m)
010-11156-01
010-11156-01
82 ft. (25 m )
82 ft. (25 m )
010-11156-02
010-11156-02
page
30.