Garmin Pro 550 Plus Panduan Pemilik - Halaman 6
Jelajahi secara online atau unduh pdf Panduan Pemilik untuk Produk Perawatan Hewan Peliharaan Garmin Pro 550 Plus. Garmin Pro 550 Plus 14 halaman. Training and tracking system
Juga untuk Garmin Pro 550 Plus: Panduan Pemilik (24 halaman)
Halaman Cetak
1
Lift the weather cap
.
2
Plug the small end of the power cable into the mini-USB port
on the device.
3
Plug the other end of the power cable into a power source.
The status LED is solid red when the device is charging.
4
After the status LED turns solid green, unplug the power
cable from the device.
Charging the Dog Collar Device
To prevent corrosion, thoroughly dry the contacts on the collar
and the surrounding area before connecting the charging clip.
NOTE: Your dog collar device may look different than the device
pictured.
You should fully charge the battery before you use the device for
the first time. Charging a fully depleted battery takes about five
hours.
1
Snap the charging clip
2
Plug the small end of the power cable into the mini-USB port
on the charging clip cable.
3
Plug the power cable into a power source.
The status LED is solid red when the collar is charging.
4
After the status LED turns solid green, remove the charging
clip from the collar.
Turning On the Device
• On the handheld device, press the power key.
• On the dog collar device, hold the power key until the status
LED flashes and the collar beeps.
Turning Off the Device
• On the handheld device, hold the power key.
• On the dog collar device, hold the power key until the status
LED turns red.
Acquiring Satellite Signals
Both the dog collar device and the handheld device must
acquire satellite signals before you put the dog collar device on
your dog. Acquiring satellite signals can take a few minutes.
1
Go outdoors to an open area.
2
Turn on both devices
(Turning On the Device, page
2
NOTICE
onto the device
.
3
On the handheld device, select a paired collar with the toggle
switch.
When the dog collar device has acquired satellite signals, the
status LED flashes a double-blink or triple-blink in green. When
the handheld device has acquired satellite signals and
communicated with a paired dog collar device, it displays status
information for the dog collar device
page
1).
Dog Collar Device
You can use up to 3 dog collar devices with a single handheld
device.
Each dog collar device must be paired with the handheld device
before it can be used. During the pairing process, each dog
collar device is associated with a different color on the handheld
device.
Pairing a Dog Collar Device with the Handheld Device
NOTE: If your handheld device and dog collar device were
included in the same package, the devices are already paired.
1
Turn on the handheld device
page
2).
2
Select a color with the toggle switch.
The dog collar device will be assigned to this color.
3
Turn the intensity dial to N.
4
Select the green tone key.
5
Select the top training key.
6
Follow the on-screen instructions to select auto, tree, or point
for the type of dog wearing the collar.
appears on the handheld device screen. The handheld
device is ready to pair. You can cancel pairing by pressing
the green tone key.
7
If the dog collar device is on, turn it off
Device, page
8
Hold the power key on the dog collar device until it emits two
series of beeps (about 2 seconds), and then release the
power key.
The status LED flashes green rapidly. You can now pair the
dog collar device with the handheld device.
The handheld device vibrates and a check mark appears on the
screen when the devices have paired successfully.
TIP: You must obtain GPS signals on both devices before the
handheld device displays the dog collar device battery status,
distance, and direction
Selecting a Dog Collar Device
Before you can select and control a dog collar device, you must
pair the dog collar device with the handheld device
Dog Collar Device with the Handheld Device, page
Move the dog collar device toggle switch to select the color
associated with a dog collar device.
The training keys control the dog collar device associated with
the selected color.
Fitting the Collar on Your Dog
To prevent irritation from the contact points, remove the collar
for at least eight hours out of every 24-hour period.
This device is not intended for human use. Do not attempt to
use on any person.
Do not spray the device or collar with harsh chemicals including
but not limited to flea or tick spray. Always ensure that any flea
or tick spray that is applied to the dog is completely dry before
2).
(Handheld Device Screen,
(Turning On the Device,
(Turning Off the
2).
(Acquiring Satellite Signals, page
CAUTION
2).
(Pairing a
2).
Getting Started