Garmin Sport PRO Panduan Pemilik - Halaman 6
Jelajahi secara online atau unduh pdf Panduan Pemilik untuk Produk Perawatan Hewan Peliharaan Garmin Sport PRO. Garmin Sport PRO 12 halaman. Dog collar device gps
Juga untuk Garmin Sport PRO: Panduan Pemilik (20 halaman)
Halaman Cetak
2
Plug the power cable into a power source.
The status LED is solid red when the collar is charging.
3
After the status LED turns solid green, remove the charging
clip from the collar.
Turning On the Dog Collar Device
• To turn on the dog collar device in training mode, hold the
power key until the status LED turns green and the collar
beeps.
• To turn on the dog collar device in independent BarkLimiter
mode, hold the power key until the status LED turns blue
(Enabling the Independent BarkLimiter Feature from the Dog
Collar Device, page
4).
• To turn on the dog collar device in pairing mode, hold the
power key until the status LED turns yellow
Collar Device with the Handheld Device, page
Turning Off the Device
1
On the dog collar device, hold the power key until the status
LED turns red.
2
Release the power key.
The dog collar device beeps to confirm powering off.
NOTE: If the device is powered off in BarkLimiter mode, the
LED flashes the number of corrected barks before powering
off
(Bark Odometer
, page
™
Dog Collar Device
You can use up to 3 dog collar devices with a single handheld
device.
Each dog collar device must be paired with the handheld device
before it can be used. During the pairing process, each dog
collar device is associated with a different color on the handheld
device.
Pairing a Dog Collar Device with the Handheld Device
NOTE: If your handheld device and dog collar device were
included in the same package, the devices are paired from the
factory.
1
On the handheld device, move the toggle switch to choose
the color associated with the dog collar device.
2
On the handheld device, set the intensity level to a numbered
position.
3
On the dog collar device, hold the power key for about 5
seconds until the status LED turns yellow.
4
While the dog collar device status LED is yellow, select a
training key on the handheld device.
The dog collar device beeps when the devices have paired
successfully.
TIP: If the devices did not pair successfully, you should verify
the batteries in both devices are fully charged and the intensity
level is set to a numbered position.
Selecting a Dog Collar Device
Before you can select and control a dog collar device, you must
pair the dog collar device with the handheld device
Dog Collar Device with the Handheld Device, page
2
(Pairing a Dog
2).
4).
(Pairing a
2).
Move the dog collar device toggle switch to select the color
associated with a dog collar device.
The training keys control the dog collar device associated with
the selected color.
Fitting the Collar on Your Dog
To prevent irritation from the contact points, remove the collar
for at least eight hours out of every 24-hour period.
This device is not intended for human use. Do not attempt to
use on any person.
Do not spray the device or collar with harsh chemicals including
but not limited to flea or tick spray. Always ensure that any flea
or tick spray that is applied to the dog is completely dry before
placing the collar on the dog. Small amounts of harsh chemicals
can damage the plastic components and collar laminate.
In order to effectively train the dog, the collar and device must fit
the dog properly. If the collar is too loose or positioned
incorrectly, stimulation may be inconsistent. This can delay or
prevent successful training.
1
Position the device at the front of the dog's neck, with the
status LED facing toward the dog's chin and the contact
points against the throat.
TIP: For bark correction, the device contact points should be
positioned near the dog's vocal cords. This location varies
based on the breed of dog. If the device does not seem to
detect the dog's barks, you should move the device closer to
or farther from the dog's body to find the ideal location.
2
Tighten the strap so that it is very snug around the dog's
neck, and fasten the buckle.
NOTE: The collar should fit tightly and should not be able to
rotate or slide on the dog's neck. The dog must be able to
swallow food and water normally. You should observe your
dog's behavior to verify that the collar is not too tight.
3
Wiggle the device to work the contact points through the
dog's coat.
NOTE: The contact points must have contact with the dog's
skin to be effective.
4
If the strap is too long, cut off the excess, leaving at least
8 cm (3 in.) to spare.
TIP: You can mark the hole used to fasten the buckle for
future reference.
Selecting and Installing the Contact Points
For best results, select the correct contact points based on your
dog's coat.
CAUTION
Getting Started